TITLE

Testing Research is about the influence of the diameter of the bearing push-extend reamed to the Bearing Capability of the Pile of Push-extend Multi-under-reamed Pile

AUTHOR(S)
Yongmei Qian; Rongzheng Zhai; Xiaolong Liu
PUB. DATE
July 2014
SOURCE
Applied Mechanics & Materials;2014, Issue 578-579, p192
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
In this paper, through the experimental study about the stress of soil around the pile when the bearing push-extend reamed have different diameters, observed the destruction of soil around the pile. Further determined the destruction of soil form, verify the theoretical analysis results of the influence for bearing capacity of the push-extend Multi-under-reamed pile in the different diameter of the bearing push-extend reamed. It provided a reliable basis of comprehensive considering the factors influencing of the Push-extend Multi-under-reamed Pile in the actual design.
ACCESSION #
99665503

 

Related Articles

  • Three-Dimensional Stress State of an Orthotropic Rectangular Prism under a Transverse Force Applied at its End. Revenko, V. // International Applied Mechanics;Apr2005, Vol. 41 Issue 4, p367 

    The exact three-dimensional elastic solution is found for an orthotropic composite rectangular prism (plate) bent by a transverse force applied to its end. The three-dimensional distribution of stresses and displacements is obtained. The distribution of tangential stresses in the prism and plate...

  • Shake-Table Tests of a Concrete Frame Sustaining Column Axial Failures. Ghannoum, Wassim M.; Moehle, Jack P. // ACI Structural Journal;May/Jun2012, Vol. 109 Issue 3, p393 

    Earthquake simulation tests of a one-third-scale, three-story, three-bay, planar reinforced concrete frame were conducted to gain insight into the dynamic collapse of older-type construction. Collapse of the frame was the result of shear and axial failures of columns with widely spaced...

  • Verification of the Geometric Parameters of the Ring-Core Method. ŠARGA, Patrik; MENDA, František; TREBUŇA, František // Applied Mechanics & Materials;2016, Vol. 827, p109 

    The Ring-Core method is a semi-destructive method for residual stress determination inside materials. The evaluation of residual stresses using Ring-Core method requires complex analysis of the geometric parameters. This work deals with the uniformly distributed residual stress components...

  • Numerical Simulation of Internal Defects in CSG Concrete (IV). Jing Ma; Yan Wang; Lingqiang Yang // Advanced Materials Research;2014, Vol. 1065-1069, p1817 

    The objective of this paper is to quantify the influence of internal defect on the multiaxial strength. Numerical analyses are performed for the second and third axial strength of the concrete. The analysis result indicated the existence of defects not only decreases the strength of materials,...

  • Study on the stress and strain of EPS silt light-weight soil by laboratory test. Yong Feng; Yubin Pei // Applied Mechanics & Materials;2014, Issue 580-583, p499 

    EPS is silt mixing light-weight soil by expanded polystyrene, curing agent, mixture mixing and has a certain strength, lightweight synthetic packing. This article is based on laboratory test, using the uniaxial and triaxial compression test on the relationship between stress and strain, research...

  • Simplified Method for Estimating the Inner Support and Internal Force through Stand Column Uplift of Foundation Pit in Soft Soil. Yan Liu; Junyan Liu; Tao Liu // Applied Mechanics & Materials;2014, Issue 580-583, p474 

    In the excavation process of Foundation Pit in Soft Soil area, it will cause the large uplift of stand column, and may cause the instability and failure of foundation pit in case of being serious; but the additional internal force of support system caused by the uplift and sinking of stand...

  • Ultimate Bearing Capacity Analysis of Oblique Beam System Supported by Knee Brace. Lehman Xu; Feng Liu; Shuangshuang Meng // Applied Mechanics & Materials;2014, Issue 578-579, p602 

    This article established the oblique beam system supported by knee brace in portal frame by using finite element software ANSYS. We analysed the ultimate bearing capacity of the system, and discussed the effects of purlin stiffness and knee brace layout on the bearing capacity of the structure....

  • Radiation effects on two-dimensional MHD Falkner-Skan wedge flow. Abdulhameed, M.; Saleh, H.; Hashim, I.; Roslan, R. // Applied Mechanics & Materials;2015, Vol. 773-774, p368 

    Radiation effects on two-dimensional MHD Falkner-Skan boundary layer wedge have been studied. Analytical solution of nonlinear boundary-layer equations is obtained by modified homotopy perturbation method. It is observed that the magnetic field tends to decelerate fluid flow whereas radiations...

  • DESIGN FOR TWO-FLUID FINE NOZZLE WITH 50% FILL RATIO. ASMUIN, Norzelawati // Applied Mechanics & Materials;2015, Vol. 773-774, p387 

    Sufficient air insert by reduced liquid in flashing propellants are required to produce fine droplet size with symmetrical spray in an aerosol atomiser without swirling design. It is called novel matched valve-actuator with two-fluid fine nozzle. Two-fluid fine nozzle design is an arrangement...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics