TITLE

Effect of Different Thickness of Core Layer on Tensile Properties of Laminated Natural Rubber Latex Film

AUTHOR(S)
SIDEK, MUFIDAH MD; RASHID, AZURA A.; AZAHARI, BAHARIN
PUB. DATE
September 2014
SOURCE
Advanced Materials Research;2014, Vol. 1024, p259
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Laminated natural rubber latex (NR) latex for mould cleaning application was prepared by arranging half-cured latex sheets with various thicknesses of core layer. Laminated layers consist of outer layer (NR latex films with cleaning agent) and core layer (waste natural NR latex film). The core layer with three different thickness and control thickness of outer layer are prepared through casting method with different thickness. The effects of different thickness of core layer with different moulding temperature of 120°C, 140°C and 160°C on tensile and swelling properties of laminated NR films were investigated. The tensile test was carried out to acquire good interfacial adhesion between the laminates films. From the results obtained, sample 10L shows the highest tensile strength at 120°C. While at 140°C and 160°C moulding temperature, the highest tensile strength shows by sample 3OL.
ACCESSION #
99422917

 

Related Articles

  • Effect of Lamination Layers on Tensile Properties and Mould Cleaning Efficiency of Laminated NBR Latex Composite. RASHID, AZURA A.; SIDEK, MUFIDAH MD; TAN SVIN CHEAN // Advanced Materials Research;2014, Vol. 1024, p189 

    Mould cleaning process is the process of removal build-up deposited or residue material on the mould surface after repeated cycles of production. The currently used mould cleaning process is sand blasting (abrasive process) and dry rubber mould cleaning compounds (depends on the skill of the...

  • Rubber Wood Fibre Based Flexible Composites: Their Preparation, Physical Strength Reinforcing and Stab Resistance Behaviour. K. C. Yong // Polymers & Polymer Composites;2014, Vol. 22 Issue 4, p375 

    Novel flexible laminated composites based on rubber compounds and rubber (Hevea brasiliensis) wood fibres were successfully produced by using a carboxylated nitrile latex based adhesive system. All these laminated composites exhibited good reinforcing behaviour and strong elastomeric features....

  • 956. Research on isolation property of prestressed thick rubber bearings. Lihua Zou; Kai Huang; Yu Rao; Run Guo; Zhixu Xu // Journal of Vibroengineering;Mar2013, Vol. 15 Issue 1, p383 

    To overcome the shortages of current laminated rubber bearings (RB), a new kind of isolator called Prestressed Rubber Bearing (PRB) is presented in this paper, which is invented by appropriately amplifying the thickness of rubber layers in conventional RB and employing prestress tendons. Based...

  • Experimental Investigation on the Impact of Presence of Natural Fibre on the Mechanical Performance of a Light Weight Hybrid Bonded Laminate. Vasumathi, M.; Murali, Vela // International Journal of Engineering & Technology (0975-4024);Feb/Mar2014, Vol. 6 Issue 1, p236 

    Natural fibres play a vital role in the area of composites and have found wide acceptance in this area. In this work, two kinds of hybrid laminates are studied, one with carbon, jute and aluminium termed as CAJRAL and the other, CARAL, with carbon and aluminium only. The purpose of this study is...

  • Experimental Investigation on the Tensile Strength of Composite Laminates Containing Open and Filled Holes. Fan, X.; Qin, W.; Suo, T. // Strength of Materials;Mar2014, Vol. 46 Issue 2, p270 

    An experimental study is performed to evaluate the effects of clamping pressure, friction, and washer size on the static performance of composite laminates with open and bolt-filled holes. The static tensile strength and failure behavior of composite laminates with an open hole and a bolt-filled...

  • Investigation on the Tensile Strength of GLARE Laminate with a Hole. Gui-Min QU; Bo-Ru LI; Li ZHAO; Xiao-Feng LI // Advanced Materials Research;2014, Issue 1052-1053, p358 

    As for the case of tensile plastic deformation of glass fiber reinforced aluminum laminates (GLARE), the finite element analysis model of the tensile strength of GLARE laminates with a hole is established by means of ABAQUS software under tensile load. The modeling is found to be in good...

  • Web Lines ∣ Curl Mechanics Pt. 1--Machine Direction Curl. Walker, Timothy J. // Paper, Film & Foil Converter;7/1/2013, p4 

    The article discusses the curl in coated and laminated products. It explains that curl is created at differential strains of two bonded materials and that machine direction (MD) curl is caused by the proportionality of the percent elastic strain in a web to the tensile stress of the web. It...

  • Influence of residual stresses on the damage of composite laminates under tensile loading. WEN Zhongmeng; GONG Xiao Lu // Applied Mechanics & Materials;2015, Vol. 784, p361 

    This work investigates the effect of residual stresses on the damage of composite laminates. The incremental hole-drilling method is used to determine residual stresses in composite laminates [02/θ2]s and then acoustic emission technique is used for the identification of damage appearance...

  • Study of the Formability of Light Metallic Materials. GIRJOB, Claudia; RACZ, Gabriel; BOLOGA, Octavian; Cristina, BIRIS // Applied Mechanics & Materials;2015, Vol. 809/810, p289 

    There is a continuing interest in using laminated materials for the production of lightweight parts, the resulting parts having the same functionality and even an increased stiffness and length of operation compared to conventional materials. The present paper aims to study the forming behavior...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics