TITLE

New method of hot rolling for fabricating anisotropic Pr-Fe-B-based magnets

AUTHOR(S)
Mukai, T.; Sakamoto, H.
PUB. DATE
April 1989
SOURCE
Applied Physics Letters;4/17/1989, Vol. 54 Issue 16, p1597
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
A unique method of hot rolling is described which fabricates high performance plate-shaped magnets from a cast Pr17Fe76.5B5Cu1.5 alloy. A flat ingot of the alloy with fine-scale columnar grains of a Pr2Fe14B phase is prepared by chill casting. The ingot is hot rolled in such a way that the roll pressure is applied perpendicular to the preferential growth direction of the columnar grains. A maximum energy product of 25.3 MG Oe has been obtained by this method.
ACCESSION #
9830822

 

Related Articles

  • An investigation of descaling spray on microstructural evolution in hot rolling. Wang, F.; Ning, L.; Zhu, Q.; Lin, J.; Dean, T. // International Journal of Advanced Manufacturing Technology;Aug2008, Vol. 38 Issue 1/2, p38 

    High pressure water spray is used to remove oxide scales in hot rolling of steel plate. This would reduce the temperature temporarily on the workpiece surface. To investigate the effect of temperature variation due to the descaling spray on the microstructural evolution, a thermal-mechanical...

  • Nd-Fe-B die-upset and anisotropic bonded magnets (invited). Nozawa, Y.; Iwasaki, K.; Tanigawa, S.; Tokunaga, M.; Harada, H. // Journal of Applied Physics;11/15/1988, Vol. 64 Issue 10, p5285 

    Focuses on a study which investigated the hot working conditions for neodymium-iron-boron die-upset magnets. Variation in magnetic properties after hot working; Magnetization curves for die-upset magnets; Examination of the processing parameters for die-upset magnets.

  • Hot workability of melt-spun Nd-Fe-Co-B magnets. Yoshida, Y.; Kasai, Y.; Watanabe, T.; Shibata, S.; Panchanathan, V.; Croat, J. J. // Journal of Applied Physics;4/15/1991, Vol. 69 Issue 8, p5841 

    Presents a study which examined the hot workability of melt-spun neodymium-iron-cobalt-boron (Nd-Fe-Co-B) magnets. Experimental procedure; Deformation behavior of Nd-Fe-Co-B; Effect of working conditions on magnetic properties.

  • Reasons for the formation and growth of edge cracks on hot-rolled plates of steel 10KhSNDA. Kuklev, A. V.; Sosnin, V. V.; Longinov, A. M.; Barantseva, I. V.; Ziborov, A. V.; Zyryanov, V. V.; Kulagin, S. A.; Kuznetsov, M. S.; Kotel'nikov, G. I. // Metallurgist;May2008, Vol. 52 Issue 5-6, p289 

    A thorough study of the technology used to obtain hot-rolled plates of steel 10KhSNDA at Ural Steel determined the mechanism responsible for the formation and growth of edge cracks in the plates. The implementation of suitable technical measures has reduced the incidence of plate rejection for...

  • Feasibility Analysis of the Production of Hot-Rolled Ferritic-Martensitic Steels on a 2000 Mill. D’yachenko, V.; Denisov, S.; Gorbunov, A.; Vetrenko, A.; Shchurov, G.; Brus’yanina, A.; Pimenov, V. // Metallurgist;May2008, Vol. 52 Issue 5-6, p293 

    The main parameters in the technology chosen to make high-strength dual-phase steel are: an alloying system that may or may not include molybdenum; the use of a spraying scheme on the cooling bed of the hot-strip mill that realizes three-stage cooling: first accelerated cooling → air...

  • Measurement of Semifinished-Product Temperature During Shaping Operations Using a Thermal Imaging Method. Kharitonov, E.; Alekseev, P.; Romanenko, V. // Metallurgist;May2005, Vol. 49 Issue 5/6, p254 

    An experimental method which has been developed makes use of thermal vision to study the temperature of metal during hot shaping. The method also uses a computer to analyze video images and does not require costly equipment. It is suited for noncontact measurement of the surface of heated...

  • Hot rolled coil property heterogeneities due to coil cooling: impact and prediction. Jacolot, Ronan; Huin, Didier; Marmulev, Artem; Mathey, Eliette // Key Engineering Materials;2014, Vol. 622-623, p919 

    The importance of coil cooling conditions on mechanical properties uniformity of HSLA and AHSS steel grades is discussed. It is namely shown that hot rolled coil under conventional industrial production can be cooled non-uniformly. That is why to predict correctly the final steel microstructure...

  • Application of Dynamic Deadband Eccentricity Filter in GM-AGC System. Dong Li; Weixing Song; Caijin Zhang; Jianchang Liu; Shubin Tan; Shuai Hou; Jianming Li; Junyan Xu // Materials Science Forum;2014, Vol. 789, p587 

    The problem of roll eccentricity has become one of important factors to affect the quality of strips as downstream industries require improvement of the strip quality. Reducing thickness control precision as little as possible is incompatible with restraining roll eccentricity perturbations on...

  • The effect of mechanical working on the in-plane magnetic properties of Hiperco 50. Storch, M.L.; Rollett, A.D. // Journal of Applied Physics;4/15/1999 Part 2B of 2, Vol. 85 Issue 8, p6040 

    Focuses on a study on the effect of mechanical working on the in-plane magnetic properties of Hiperco 50, a soft magnetic material. Measurement of the effect of different rolling schedules; Pole figure analysis; Conclusions.

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics