TITLE

Improved flash γ-ray uniformity using a Bθ lens diode

AUTHOR(S)
Sanford, T. W. L.; Halbleib, J. A.; Poukey, J. W.; Heath, C. E.; Mock, R.; Bailey, V. L.; Proulx, G. A.; Spence, P. W.; Kishi, H.
PUB. DATE
April 1989
SOURCE
Applied Physics Letters;4/10/1989, Vol. 54 Issue 15, p1406
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Significantly improved spatial uniformity of bremsstrahlung radiation, relative to a planar-anode diode, is obtained on the 3-MV, 150-kA HELIA accelerator when a Bθ lens diode is used to actively control the high-power electron beam at the exit of a coaxial, magnetically insulated transmission line. The advantage of this diode over other diodes which only passively control the beam is that better radiation uniformity for less beam loss is possible. Measurements taken on HELIA are shown to agree with theoretical expectations.
ACCESSION #
9830692

 

Related Articles

  • X-ray emission from 30 J Blumlein operated compact diode. Zakaullah, M.; Worley, J. // Journal of Applied Physics;8/1/2000, Vol. 88 Issue 3, p1251 

    Studies an x-ray emitting diode with a knife-edge cathode energized by a 90 kV, 30 J, solid dielectric Blumlein driver of pulse length 10 ns. X-ray emission from titanium, copper, molybdenum, tin, tantalum and lead anodes; Ratio of line to continuum with molybdenum target.

  • Anode-temperature dependence of ion beam turn-on time in magnetically insulated pulsed ion diodes. Yoneda, H.; Horioka, K.; Ohbayashi, K.; Kasuya, K. // Applied Physics Letters;5/5/1986, Vol. 48 Issue 18, p1196 

    The temperature effect of anode dielectric materials on ion beam turn-on time is examined in a magnetically insulated pulsed ion diode. It is observed that the turn-on time decreased with temperature increase. This effect may be explained by a simple model in which electrons bombard the anode...

  • Optical characteristics of the hollow anode discharge. Miljevic, Vujo I. // Journal of Applied Physics;1/15/1986, Vol. 59 Issue 2, p676 

    Presents a type of discharge realized in a diode consisting of a concave cathode and a special type of a hollow anode. Arrangement of dark and luminous regions between the cathode and anode; Reason for the use of hollow anode discharge as an ion-electron source; Comparison between the hollow...

  • Anode foil changer for high-current relativistic electron beam diode systems. Fine, T. A.; Rhee, M. J. // Review of Scientific Instruments;Nov89, Vol. 60 Issue 11, p3556 

    An anode foil changer for pulsed, high-current, relativistic electron beam diode systems is described. This device allows multiple shots to be taken with a foil-anode diode system while maintaining a continuous vacuum. Shot-to-shot reproducibility is greatly improved, while at the same time a...

  • Electron flow in the pinch region of a relativistic electron-beam diode. Markovits, M.; Nardi, E.; Zinamon, Z. // Physics of Fluids (00319171);Mar85, Vol. 28 Issue 3, p971 

    The flow of electrons produced in the pinch region of a relativistic electron beam (REB) diode is studied by means of the time-dependent Kα emission from a double-layered anode. The anode materials were Cu and Ni foils of various thicknesses. The experimental data were analyzed using detailed...

  • Polyaniline and poly (N-vinylcarbazole) blends as anode for blue light-emitting diodes. Jinkoo Chung; Beomrak Choi // Applied Physics Letters;6/14/1999, Vol. 74 Issue 24, p3645 

    Reports on the successful introduction of a polyaniline (PANI) anode that is blend with poly(N-vinylcarbazole) or PVK for organic light-emitting diodes (OLED). Comparison with the usual PANI network electrodes; Simpler fabrication; Better planarized surface; Vapor-deposited emitting layer.

  • Lithium–fluoride-modified indium tin oxide anode for enhanced carrier injection in phenyl-substituted polymer electroluminescent devices. Zhu, Furong; Low, Beeling; Zhang, Keran; Chua, Soojin // Applied Physics Letters;8/20/2001, Vol. 79 Issue 8, p1205 

    Phenyl-substituted polymer electroluminescent (EL) devices using an insulating lithium–fluoride (LiF) layer between indium tin oxide (ITO) and poly(styrene sulfonate)-doped poly(3,4-ethylene dioxythiophene) (PEDOT) hole transporting layer have been fabricated. By comparing the devices...

  • Improved operational stability of polyfluorene-based organic light-emitting diodes with... Kim, J. S.; Friend, R. H. // Applied Physics Letters;5/24/1999, Vol. 74 Issue 21, p3084 

    Studies the influence of various surface treatments of indium-tin-oxide anodes on the operational stability of high efficiency green-emitting polymer light emitting diodes. Anode modification by physical, chemical and combined treatments; Effects of oxygen plasma on the stability under constant...

  • Enhanced hole injections in organic light-emitting devices by depositing nickel oxide on indium tin oxide anode. Chan, I-Min; Hsu, Tsung-Yi; Hong, Franklin C. // Applied Physics Letters;9/2/2002, Vol. 81 Issue 10, p1899 

    An ultrathin layer of nickel oxide (NiO) was deposited on the indium tin oxide (ITO) anode to enhance the hole injections in organic light-emitting diode (OLED) devices. A very low turn-on voltage (3 V) was actually observed for the device with NiO on ITO. The enhancement of hole injections by...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics