TITLE

Unlubricated friction and wear of an ion beam mixed, nitrogen-implanted Fe50Ti50 surface alloy on AISI 304 stainless steel

AUTHOR(S)
Hirvonen, J-P.; Nastasi, M.; Mayer, J. W.
PUB. DATE
July 1987
SOURCE
Applied Physics Letters;7/27/1987, Vol. 51 Issue 4, p232
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Nitrogen implantation was observed to significantly improve the dry sliding properties of an ion beam mixed Fe50Ti50 surface alloy on AISI 304 stainless steel. Implantation to the fluence of 1.7×1017 N/cm2 at 50 keV increased the wear resistance but a decreased friction coefficient was obtained only after few hundred cycles at the beginning of the pin-on-disk test. When nitrogen was implanted to the fluence of 3×1017 N/cm2 an improved wear resistance and decreased friction were detected throughout the test of 1000 cycles. In addition, good sliding properties were also found at higher loads in the high fluence, nitrogen-implanted samples. These results differ from those obtained following a nitrogen implantation into Ti-implanted iron or iron-based alloys and are attributed to higher titanium and nitrogen concentrations.
ACCESSION #
9823622

 

Related Articles

  • Brazing Ceramic to Stainless Steel Enhanced by Surface Modification. Kyu-Yong Lee // Welding Journal;Sep2007, Vol. 86 Issue 9, p35 

    The article discusses a method for brazing alumina ceramics to SUS304 stainless steel with improved joint strength. The method joins the ceramics to the stainless steel using a metallic filler with active metal elements between the ceramic and metal substrate. The process takes advantage of both...

  • Evidence of Substrate Melting of NiCr Particles on Stainless Steel Substrate by Experimental Observation and Simulations. Tran, A. T. T.; Brossard, S.; Hyland, M. M.; James, B. J.; Munroe, P. // Plasma Chemistry & Plasma Processing;Dec2009, Vol. 29 Issue 6, p475 

    Single NiCr splats were plasma-sprayed onto a polished stainless steel substrate held at room temperature. The splat-substrate interface was characterized by focused ion beam and transmission electron microscopy. The frequent observation of NiO particles, particularly in pores within the splat,...

  • Anisotropic ion-enhanced diffusion during ion nitriding of single crystalline austenitic stainless steel. Martinavicˇius, A.; Abrasonis, G.; Möller, W.; Templier, C.; Rivière, J. P.; Declémy, A.; Chumlyakov, Y. // Journal of Applied Physics;May2009, Vol. 105 Issue 9, p093502 

    Nitrogen diffusion is investigated in single crystalline austenitic stainless steel AISI 316L during ion beam nitriding and subsequent annealing at three different crystalline orientations. After nitriding at 400 °C and ion energy of 1 keV, the N penetration depth depends significantly on the...

  • Residual stress in nano-structured stainless steel (AISI 316L) prompted by Xe+ ion bombardment at different impinging angles. Cucatti, S.; Droppa Jr, R.; Figueroa, C. A.; Klaus, M.; Genzel, Ch.; Alvarez, F. // Journal of Applied Physics;2016, Vol. 120 Issue 14, p1 

    The effect of low energy (<1 keV) xenon (Xe+) ion bombardment on the residual stress of polycrystalline iron alloy (AISI 316L steel) is reported. The results take into account the influence of the ion incident angle maintaining constant all other bombarding parameters (i.e., ion energy and...

  • Outstanding Meeting Paper: Interface control in all metalorganic deposited coated conductors: Influence on critical currents. Pomar, Alberto; Coll, Mariona; Cavallaro, Andrea; Gàzquez, Jaume; Mestres, Narcis; Sandiumenge, Felip; Puig, Teresa; Obradors, Xavier // Journal of Materials Research;Sep2006, Vol. 21 Issue 9, p2176 

    In this work, we report recent progress in the control of the interface quality between buffer layers and YBa2Cu3O7 (YBCO) thin films grown by the trifluoroacetates route (TFA) and how it influences the critical current Jc of the coated conductors (CCs). We have mainly focused on the two most...

  • Comprehensive Analysis of Ion Beam Induced Stainless Steel Surface Morphology. Kowalski, Z. W. // Acta Physica Polonica, A.;Jul2011, Vol. 120 Issue 1, p70 

    Surface morphology, one of the various physical properties modified by ion beam irradiation, is usually characterized by well known and very often investigated surface topography and surface roughness. The paper presents two additional aspects of surface morphology modification (called by the...

  • Behavior of nitrided and carburized AISI 904L stainless steels under severe light ion beam irradiation with plasma focus. Molleja, J. García; Gómez, B. J.; Bürgi, J.; Feugeas, J.; Milanese, M.; Moroso, R.; Niedbalski, J.; Piccoli, M.; Bemporad, E. // Surface & Interface Analysis: SIA;Jun2015, Vol. 47 Issue 6, p728 

    Superaustenitic stainless steels have become of growing interest in industrial and technological fields, but there is not a complete understanding on their fundamental properties and their performances. For this paper, AISI 904 L superaustenitic samples were nitrided and carburized in order to...

  • Effect of Ion-Energy on the Properties of Amorphous GaN Films Produced by Ion-Assisted Deposition. Lanke, Uday; Koo, Annette; Granville, Simon; Trodahl, Joe; Markwitz, Andreas; Kennedy, John; Bittar, Antoine // Modern Physics Letters B;12/20/2001, Vol. 15 Issue 28/29, p1355 

    Amorphous GaN films were deposited on various substrates viz. Si (100), quartz, glass, Al, stainless steel and glassy carbon by thermal evaporation of gallium in the presence of energetic nitrogen ions from a Kaufman source. The films were deposited at room temperature and 5 × 10-4 mbar...

  • Patterned Exfoliation of GaAs Based on Masked Helium Implantation and Subsequent Rapid Thermal Annealing. Woo, H. J.; Choi, H. W.; Kim, G. D.; Hong, W.; Kim, J. K. // AIP Conference Proceedings;3/15/2009, Vol. 1099 Issue 1, p535 

    A method of patterning single crystal GaAs based on ion implantation induced selective area exfoliation is suggested. Samples were implanted with 200–500 keV helium ions to a fluence range of 2–4×1016 He+/cm2 at room temperature through masks of Ni mesh (40 μm opening) or...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics