TITLE

Plasma sprayed Fe76Nd16B8 permanent magnets

AUTHOR(S)
Overfelt, R. A.; Anderson, C. D.; Flanagan, W. F.
PUB. DATE
December 1986
SOURCE
Applied Physics Letters;12/29/1986, Vol. 49 Issue 26, p1799
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Thin coatings (0.16 mm) and thick coatings (0.50 mm) of Fe76Nd16B8 were deposited on stainless-steel substrates by low pressure plasma spraying. Microscopic examination of the coatings in a light microscope revealed excessive porosity, but good bonding to the substrate. Fracture cross sections examined in a scanning electron microscope showed the grains to be equiaxed and approximately 1 μm or less in diameter in the as-sprayed condition. The intrinsic coercivities of the as-sprayed coatings varied from 5.8 to 10.9 kOe. The effects of post-spray heat treatments on the intrinsic coercivity are also given.
ACCESSION #
9821759

 

Related Articles

  • Ablation Property of the Plasma Sprayed NiCrAlY-ZrO2 Compound Coating on Stainless Steel Material. Zhiping DENG; Zhaohui LIU; Hang ZHANG; Yuan LI // Advanced Materials Research;2015, Vol. 1120-1121, p689 

    The NiCrAlY-ZrO2 anti-ablation compound coating was prepared on one surface of a 201stainless steel by plasma spraying, and the ablation property was studied by the cyclic ablation experiment. The morphology and XRD pattern of the NiCrAlY-ZrO2 coating were characterized by SEM and XRD methods...

  • Microstructure of 316L stainless steel coating deposited by the low pressure plasma spray. Deming Yang; Bohan Tian // Applied Mechanics & Materials;2014, Issue 644-650, p4888 

    Original equiaxed 316L stainless steel coatings were successfully deposited by the low pressure plasma spray. For comparison, the coatings of 316L stainless steel with normal lamellar structure were also prepared by the air plasma spray (APS). The microstructures were investigated using optical...

  • Influence of Preheating Temperature on the Quality of the Interface Between Plasma Sprayed Coatings and Substrate. Vilémová, Monika; Nevrlá, Barbara; Matĕjíček, Jirí; Mušálek, Radek // Key Engineering Materials;2014, Vol. 606, p183 

    This study was aimed to investigate the effect of the substrate preheating temperature on the overall quality of the coating/substrate interface. The coatings (stainless steel) were deposited using a water stabilized plasma torch (Institute of Plasma Physics, Prague, i.e. IPP, Czech Republic) on...

  • The Effect of Coating Parameter on Properties of Plasma Sprayed Co Based Coatings. ÖZEL, Serkan // Tehnicki vjesnik / Technical Gazette;2019, Vol. 26 Issue 2, p318 

    In this study, the surface of stainless steel was coated by Co based (Co, Mo, Cr) powders using plasma spray technique with different production parameters (500A, 550 A and 600 A current values) The coating layers were examined with optical microscopy, SEM, EDS and XRD analysis. The bonding...

  • Resistance to Corrosion of Zirconia Coatings Deposited by Spray Pyrolysis in Nitrided Steel. Cubillos, G.; Olaya, J.; Bethencourt, M.; Cifredo, G.; Blanco, G. // Journal of Thermal Spray Technology;Oct2013, Vol. 22 Issue 7, p1242 

    Coatings of zirconium oxide were deposited onto three types of stainless steel, AISI 316L, 2205, and tool steel AISI D2, using the ultrasonic spray pyrolysis method. The effect of the flux ratio on the process and its influence on the structure and morphology of the coatings were investigated....

  • Laser Cladding to Improve Oxidation Behavior of Air Plasma-Sprayed Ni-20Cr Coating on Stainless Steel Substrate. Rauf, M.; Shahid, Muhammad; Nusair Khan, A.; Mehmood, K. // Journal of Materials Engineering & Performance;Sep2015, Vol. 24 Issue 9, p3651 

    Air plasma-sprayed Ni-20Cr coating on stainless steel (AISI-304) substrate was re-melted using CO laser to remove the inherent defects, i.e., porosity, splat boundaries, and oxides of air plasma-sprayed coating. The (1) uncoated, (2) air plasma-sprayed, and (3) laser-re-melted specimens were...

  • Atmospheric Plasma Spraying of Al2O3 + 13% TiO2 Coatings Using External and Internal Injection System. Łatka, L.; Michalak, M.; Jonda, E. // Advances in Materials Science;Dec2019, Vol. 19 Issue 4, p5 

    The ceramic coatings based on mixture of Al2O3 and TiO2 have better properties in comparison to the pure alumina ones. Among many techniques, plasma spraying is very useful method of ceramic coatings manufacturing. In this paper, the results of microscopic, mechanical and tribological properties...

  • Thin Yttria-Stabilized Zirconia Coatings Deposited by Low-Energy Plasma Spraying Under Very Low Pressure Condition. Lin Zhu; Nannan Zhang; Fu Sun; Bolot, Rodolphe; Planche, Marie-Pierre; Hanlin Liao; Coddet, Christian // Journal of Thermal Spray Technology;Sep2011, Vol. 20 Issue 5, p1118 

    In recent decades, very low pressure plasma spraying (VLPPS) technology (less than 10 mbar), as a next-generation coating process, has been extensively studied, because it can fully evaporate the materials to deposit dense, thin, and columnar grain coatings. This research aims at applying VLPPS...

  • STAINLESS Q&A. Kotecki, Damian J. // Welding Journal;Sep2003, Vol. 82 Issue 9, p24 

    Presents an answer to the question about applying a corrosion-resistant hardfacing to the surfaces of a forcep used for animal tooth extraction. Achievement of 40 to 50 Rockwell C hardness; Suitability of 410 or 420 stainless; Issue of dilution.

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics