TITLE

Laser produced percolation structures

AUTHOR(S)
Thuillard, M.; von Allmen, M.
PUB. DATE
April 1986
SOURCE
Applied Physics Letters;4/21/1986, Vol. 48 Issue 16, p1045
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Pulsed laser irradiation of thin Ti films yields structures consisting of metallic islands connected by oxide filaments. The sheet resistivity of the structure is mostly determined by the degree of oxidation of the filaments and can be varied through the laser fluence. By adding gold to the initial layer, the same structures are obtained but oxidation is inhibited. The material is essentially a two-dimensional bond percolator. The temperature coefficient of the resistance is drastically reduced compared to that of the previously investigated Ti-TiOx structures.
ACCESSION #
9819636

 

Related Articles

  • Biocompatibility of Titanium Dioxide Film Modified by Femtosecond Laser Irradiation. Masahiro Tsukamoto; Togo Shinonaga; Akiko Nagai; Kimihiro Yamashita; Takao Hanawa; Nobuhiro Matsushita; Xie Guoqiang; Nobuyuki Abe // Materials Science Forum;2014, Vol. 783-786, p1377 

    Titanium (Ti) is one of the most widely used for biomaterials, because of its excellent anti-corrosion and high mechanical properties. In addion to these properies, the bioactivity of Ti is required. Recently, coating of the titanium dioxide (TiO2) film on Ti plate surface is useful methods to...

  • Role of atomic arrangements at interfaces on the phase control of epitaxial TiO[sub 2] films. Park, B. H.; Huang, J. Y.; Li, L. S.; Jia, Q. X. // Applied Physics Letters;2/18/2002, Vol. 80 Issue 7, p1174 

    Epitaxial rutile-TiO[SUB 2] and anatase-TiO[SUB 2] films were grown at 800°C on Al[SUB 2]O[SUB 3](1102) and LaAlO[SUB 3](001), respectively, using pulsed laser deposition. Both films showed high crystalline quality, evidenced by x-ray diffraction and high-resolution electron microscopy. The...

  • Effect of the excimer laser irradiation on sol-gel derived tungsten-titanium dioxide thin films. Joya, Yasir; Liu, Zhu // Applied Physics A: Materials Science & Processing;Jan2011, Vol. 102 Issue 1, p91 

    novel technique based on the excimer laser induced crystallization and modification of TiO thin films is being reported. W ions loaded TiO (WTO) precursor films were prepared by a modified sol-gel method and spin-coated onto microscopic glass slides. Pulsed KrF (248 nm, 13 ns) excimer laser was...

  • Pulsed laser deposition and characterization of NiTi-based MEMS prototypes. Camposeo, A.; Fuso, F.; Allegrini, M.; Arimondo, E.; Tuissi, A. // Applied Physics A: Materials Science & Processing;2004, Vol. 79 Issue 4-6, p1141 

    We report the fabrication and characterization of microelectromechanical systems (MEMS) prototypes based on a microcantilever coated with a NiTi thin film. The NiTi film was deposited by laser ablation and deposition in ultra-high vacuum. The samples were characterized from the mechanical point...

  • Laser-driven high-frequency vibrations of metal blister surface. Kononenko, T.; Sinyavsky, M.; Konov, V.; Sentis, M. // Applied Physics A: Materials Science & Processing;Sep2013, Vol. 112 Issue 3, p583 

    Time-resolved interferometric microscopy was applied to investigate laser-induced blistering of a titanium film on a silica substrate. Ablation of the titanium/silica interface by single 0.7 ns pulses within a certain fluence range results in local exfoliation of the metal film from the...

  • Growth and Characterisation of Pulsed-Laser Deposited Tin Thin Films on Cube-Textured Copper at Different Temperatures. Szwachta, G.; Gajewska, M.; Kąc, S. // Archives of Metallurgy & Materials;Jun2016, Vol. 61 Issue 2, p1031 

    High-quality titanium nitride thin films have been grown on a cube-textured copper surface via pulsed laser deposition. The growth of TiN thin films has been very sensitive to pre-treatment procedure and substrate temperature. It is difficult to grow heteroexpitaxial TiN films directly on copper...

  • Biaxially Textured Titanium Thin Films by Oblique Angle Deposition: Conditions and Growth Mechanisms. Liedtke-Grüner, Susann; Grüner, Christoph; Lotnyk, Andriy; Gerlach, Juergen W.; Rauschenbach, Bernd // Physica Status Solidi. A: Applications & Materials Science;Jan2020, Vol. 217 Issue 2, pN.PAG 

    Growing highly crystalline nanowires over large substrate areas remains an ambiguous task nowadays. Herein, a time‐efficient and easy‐to‐handle bottom‐up approach is demonstrated that enables the self‐assembled growth of biaxially textured Ti thin films composed of...

  • Pulsed laser deposition of NiTi shape memory effect thin films. Ciabattari, F.; Fuso, F.; Arimondo, E. // Applied Physics A: Materials Science & Processing;1997, Vol. 64 Issue 6, p623 

    We report for the first time on the pulsed laser deposition of NiTi shape-memory effect thin films. Using a NiTi bulk target with a 1:1 nominal stoichiometry, we deposited thin films (thickness ≈0.6 μm) on both Si(100) and Al[sub 2] O[sub 3] (100) substrates. We also produced free-standing...

  • Selective patterning and scribing of Ti thin film on glass substrate by 532 nm picosecond laser. Yung, K.; Cai, Zhixiang; Choy, H. // Applied Physics A: Materials Science & Processing;May2012, Vol. 107 Issue 2, p351 

    In this paper, the feasibility of Ti film coated on glass substrate scribed via a 532 nm picosecond laser is investigated. Laser irradiations from the film side and from the transparent substrate side are performed for comparison. Optical microscopy, SEM, surface stylus and contact resistance...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics