TITLE

Lamb wave reflection at plate edges

AUTHOR(S)
Diodati, P.; Tassi, G.; Alippi, A.
PUB. DATE
September 1985
SOURCE
Applied Physics Letters;9/15/1985, Vol. 47 Issue 6, p573
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The changing of modes taking place in Lamb wave reflected from the limiting edge of a plate is taken into consideration by evaluating the coupling of the single shear and longitudinal components, through Snell’s law. Acousto-optical probing of the acoustic field is used for studying the effect in isotropic plates, in the range of a few megahertz.
ACCESSION #
9818178

 

Related Articles

  • Acousto-optic modulation of a photonic crystal nanocavity with Lamb waves in microwave K band. Tadesse, Semere A.; Huan Li; Qiyu Liu; Mo Li // Applied Physics Letters;11/16/2015, Vol. 107 Issue 20, p201113-1 

    Integrating nanoscale electromechanical transducers and nanophotonic devices potentially can enable acousto-optic devices to reach unprecedented high frequencies and modulation efficiency. Here, we demonstrate acousto-optic modulation of a photonic crystal nanocavity using Lamb waves with...

  • Air-coupled acoustic imaging with zero-group-velocity Lamb modes. Holland, Stephen D.; Chimenti, D.E. // Applied Physics Letters;9/29/2003, Vol. 83 Issue 13, p2704 

    A Lamb wave resonance has been found that allows unusually efficient transmission of airborne sound waves through plates. This occurs at the zero-group-velocity point at the frequency minimum of the first-order symmetric (S[sub 1]) Lamb mode. At this frequency, plane waves with a range of...

  • In situ thin film thickness measurement with acoustic Lamb waves. Pei, Jun; Degertekin, F. Levent // Applied Physics Letters;4/24/1995, Vol. 66 Issue 17, p2177 

    Develops an in situ thin film thickness measurement technique utilizing acoustic Lamb waves. Capabilities of the technique; Compatibility of the acoustic sensors with plasma or chemical vapor deposition environments; Validation of the method by measuring aluminum film thickness in aluminum...

  • On one property of Lamb vector in isotropic turbulent flow. Tsinober, A. // Physics of Fluids A;Apr90, Vol. 2 Issue 4, p484 

    It is shown that the potential part of Lamb vector ?=?�u, ?=?�u, where u is an isotropic Gaussian solenoidal random field, is much larger than its solenoidal part. This result shows that purely kinematic properties of turbulent flow can lead to essential reduction of its nonlinearity...

  • Two quantitative optical detection techniques for photoacoustic Lamb waves. Noui, L.; Dewhurst, R. J. // Applied Physics Letters;8/6/1990, Vol. 57 Issue 6, p551 

    The cross calibration of two optical detection techniques is described for the monitoring of laser-generated Lamb waves. Measurements of Lamb waves using an optical beam deflection technique are compared with those using a Michelson interferometer technique. Analysis shows that phase changes in...

  • Erratum.  // Shock & Vibration;2012, Vol. 19 Issue 6, p1477 

    A correction to the article "An Optimization Scheme Based on the Local Interaction Simulation Approach and Lamb Waves for Elastic Property Estimation in Multi-Layered Composites," by A. B. Spencer et al. that was published in 2012 is presented.

  • Lamb wave interaction with light. Alippi, A.; Diodati, P.; Maccari, D.; Socino, G. // Journal of Applied Physics;8/15/1985, Vol. 58 Issue 4, p1450 

    Deals with a study which investigated the interaction of light with Lamb waves propagating in transparent plates. Simplified model of the small phase modulation effects produced on the crossing light wavefronts by an elastic periodical perturbation; Experimental data presented in supporting...

  • Reflection and scattering of the S[sub 0] Lamb mode from 3-D circular defects in plates. Diligent, O.; Lowe, M. J. S.; Cawley, P. // AIP Conference Proceedings;2002, Vol. 615 Issue 1, p231 

    A second study of the interaction of Lamb waves with a circular defect is presented. The Lamb wave mode chosen was the So mode in the low frequency-thickness regime. A three dimensional Finite Element mesh was generated, representing an area of the plate with a circular part-depth hole (33% or...

  • Lamb wave scattering by defects: A hybrid boundary element-finite element formulation. Galan, J. M.; Abascal, R. // AIP Conference Proceedings;2002, Vol. 615 Issue 1, p211 

    A hybrid Boundary Element (FE) — Finite Element (BE) Formulation is applied to study Lamb wave scattering by defects in homogeneous isotropic plates. A BE model of the neighborhood of the defect is combined with a semi-analytical FE non-reflecting boundary condition which accurately...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics