TITLE

Study of area replacement reinforcement effect for the opening of a cylinder vessel by using FEM

AUTHOR(S)
PENG Peiying; LIU Qinggang
PUB. DATE
August 2014
SOURCE
Journal of Hebei University of Science & Technology;Aug2014, Vol. 35 Issue 4, p366
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
According to stress assessment methods in the standard of steel pressure vessel- design by stress analysis (JB 4732 - 1995), two paths were constructed, including a traditional pathl and a path2 recommended by pressure vessel GB 150 - 2011, and the minimum thickness of the nozzles for openings with a diameter of 100~1 000 mm on cylinders with a diameter of 1 000~3 000 mm was designed by using finite element method (FEM). The analysis result was compared with that from area replacement method. The result shows that the area replacement method is danger than the traditional path1, but a little more conservative than the path2 appealed by GB 150 - 2011. According to the practice experiences and the finite element results, the path2 is more suitable to practical situation.
ACCESSION #
97927448

 

Related Articles

  • Contact stresses between two cylindrical bodies: cylinder and cylindrical cavity with parallel axes - Part I: Theory and FEA 3D Modeling. Brezeanu, Ligia Cristina // Interdisciplinarity in Engineering;2015, Vol. 19, p169 

    This paper presents the results of a study carried out using the Finite Element Method, on the contact stresses between two bodies: cylindrical body in a cylindrical cavity. The results are compared, following the analysis, to the results calculated on basis of the relations in H. Hertz's...

  • FEM Analysis of Stress Intensity Factors of Crack Tip. LIU Jianhui; WANG Shengnan; LU Yabing; HUANG Zongzheng // Applied Mechanics & Materials;2014, Issue 685, p224 

    Finite element method is used to analysis two-dimensional compact tension specimens which is made of 304 stainless steel and calculate stress intensity factors by J-integral. The effects of loading magnitude and crack length on stress intensity factors are analyzed. Meanwhile the errors between...

  • CLEAVAGE FRACTURE OF ULTRA-HIGH-STRENGTH STEELS. MICROSCOPIC OBSERVATIONS. NUMERICAL ANALYSIS. LOCAL FRACTURE CRITERION. Neimitz, Andrzej; Dzioba, Ihor; Janus, Urszula // Key Engineering Materials;2014, Vol. 598, p168 

    In the paper the fracture mechanisms in ultra-high-strength steel are examined. However, the emphasis is on cleavage fracture, which was observed in the whole temperature range tested. The extent of cleavage depends on the specimen thickness and temperature. The experimental program consisted of...

  • INFLUENCE OF MODELLING ON TRUSS STRESS ANALYSIS RESULTS. Šimić, Diana; Ilijaš, Tanja // Transactions of FAMENA;2012, Vol. 36 Issue 4, p73 

    In order to determine the real state of stress in a reinforced concrete truss and to determine the impact of restraint rods in the truss nodes on the stress in the beam, a theoretical and an experimental analysis of stress in reinforced concrete truss were conducted. The analytical modelling is...

  • ANALYSIS OF MIXED MODE I/II/III FRACTURE IN FOAM CORE COMPOSITE SANDWICH BEAMS. Rizov, Victor // Advances in Bulgarian Science;2013, p43 

    The capacity of the Split Cantilever Beam (SCB) for characterization of mixed-mode I/II/III fracture behavior of foam core composite sandwich constructions is evaluated theoretically. The sandwich SCB was obliquely-loaded with respect to the crack plane in order to induce general mixed-mode...

  • Strand Debonding for Pretensioned Bridge Girders to Control End Cracks. Okumus, Pinar; Oliva, Michael G. // ACI Structural Journal;Jan/Feb2014, Vol. 111 Issue 1, p201 

    Characteristic cracks occur at prestressed bridge girder ends during prestress release due to the transfer of the prestress force to the concrete. This research investigated the quantitative and qualitative impact of strand debonding on cracking through nonlinear finite element analysis (FEA)...

  • Calculating Stress Intensity Factor (Mode I) for Composite Plate with Central Crack. Al-Ansari, Luay S.; Al-Mahmud, Hashim N.; Al-Raheem, Saddam K. // International Journal of Computer Applications;Aug2013, Vol. 75 Issue 1-17, p1 

    A Stress Intensity Factor (SIF) Mode I is calculated for longitudinal composite plate with dimensions (104 mm x 40 mm) and fiber volume fraction (37.5%).The finite element method (FEM) (ANSYS) and MFree method are used for calculating the SIF of quarter model (i.e. (52 mm x 20 mm)) with constant...

  • Detailed investigation of contact deformation in ZrN/Zr multiplayer—understanding the role of volume fraction, bilayer spacing, and morphology of interfaces. Verma, Nisha; Jayaram, Vikram // Journal of Materials Research;Nov2013, Vol. 28 Issue 22, p3146 

    A systematic study was done to understand the influence of volume fractions and bilayer spacings for metal/nitride multilayer coating using finite element method (FEM). An axisymmetric model was chosen to model the real situation by incorporating metal and substrate plasticity. Combinations of...

  • Finite element analysis of medium-wheel bulldozer earth-moving shovel arm based on ANSYS. Qian Yin // Journal of Chemical & Pharmaceutical Research;2014, Vol. 6 Issue 6, p2341 

    The working system acts as an important component, its performance and reliability are the main criteria to measure the comprehensive function of a Bulldozer. Since Bulldozers are used in difficult conditions, it is required that the earth-moving shovel arms should be strong and hard enough. If...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics