TITLE

Limiting amplifier makes efficient A/D-converter driver

AUTHOR(S)
Amarandos, Mark; Swager, Anne Watson
PUB. DATE
September 1996
SOURCE
EDN;9/02/96, Vol. 41 Issue 18, p96
SOURCE TYPE
Trade Publication
DOC. TYPE
Article
ABSTRACT
Focuses on the circuit of the limiting amplifier that makes efficient analog-to-digital converter driver. Minimum and maximum input voltage required by the circuit; Circuit's operation; Design specification of the circuit.
ACCESSION #
9708081633

 

Related Articles

  • Guitar amplifier. Seely, Rodrick // Popular Electronics;Dec97, Vol. 14 Issue 12, p33 

    Provides information on how to assemble a `Chrome Classic 50' guitar amplifier. Circuit description of the amplifier; Construction of circuit board; Parts list for guitar amplifier.

  • Build a switching amplifier. Burbon, Rolando R. // Popular Electronics;Apr96, Vol. 13 Issue 4, p30 

    Discusses how to build a switching amplifier for radio. Circuit description; Parts; Construction.

  • Current amplifier boosts OTA output. Ciubotaru, Alexandru // Electronic Design;11/11/93, Vol. 41 Issue 23, p100 

    Presents a diagram for implementing a bidirectional precision current amplifier. Use in increasing the output current of an operational transconductance amplifier; Maximum value of the output current.

  • Build IF/AGC amp with four parts. Clarke, Bob // Electronic Design;5/30/94, Vol. 42 Issue 11, p89 

    Presents information on the construction of an IF/AGC amplifier that features an 82-dB AGC range. Equipment; Average emitter current; Circuit operations; Bandwidth.

  • Design equations help optimize supply bypassing for op amps. Graeme, Jerald; Baker, Bonnie // Electronic Design;6/24/96-Supplement Analog Issue, Vol. 44 Issue 13, p9 

    Focuses on using design equations to optimize supply bypassing for op amplifiers. Capacitors; Circuit models and analysis; Noise coupling; Intuitive evaluation; Power supply line inductance.

  • Board surgery reduces layout-induced harmonic distortion. Smith, Steve // Electronic Design;6/24/96-Supplement Analog Issue, Vol. 44 Issue 13, p84 

    Focuses on circuit layout for high-frequency amplifiers. Grounding; Addition of polarized signals; Cutting of ground planes; Pin supplies.

  • Wideband current-feedback amplifier. O'Farrell, Mark // Electronic Design;10/13/95, Vol. 43 Issue 21, p101 

    Presents an electronic circuit design for a differential high-gain wideband amplifier which is needed when trying to get the maximum bandwidth from multipliers like the LM1496 or MC1495. Need for such an amplifier because low-value out resistors are used, which reduces the output swing.

  • Combination filter eliminates OP AMP. Vitaljic, Frank N. // Electronic Design;9/5/94, Vol. 42 Issue 18, p79 

    Describes combined amplifiers which eliminate OP AMP. Construction of one adder/subtracter amplifier by combination of both input and feedback amplifier. INSET: Prototype and design equations for state variable filter..

  • Design tips for fast difference amplifiers. Baker, Bonnie C. // Electronic Design;10/14/96, Vol. 44 Issue 21, p107 

    Offers design tips for fast difference amplifiers. Use of voltage or current feedback topology; Input termination; Rejection of common mode signals; Resistor adjustments.

  • Clamp amp serves as sync inserter. Checkovich, Peter // Electronic Design;10/14/96, Vol. 44 Issue 21, p132 

    Presents an electronic circuit design for a clamp amplifier that serves as a sync inserter. Circuit description; Video signal connections; Alternative configuration; Signal appropriation.

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics