TITLE

Diode-pumped Yb:Y[sub 2]O[sub 3] ceramic laser

AUTHOR(S)
Kong, J.; Lu, J.; Takaichi, K.; Uematsu, T.; Ueda, K.; Tang, D. Y.; Shen, D. Y.; Yagi, H.; Yanagitani, T.; Kaminskii, A. A.
PUB. DATE
April 2003
SOURCE
Applied Physics Letters;4/21/2003, Vol. 82 Issue 16, p2556
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
We report on a diode-pumped polycrystalline Yb:Y[SUB2]O[SUB3] ceramic laser. We demonstrate that, with a pump power of 11 W at 937 nm, 0.75-W cw laser output at 1078 nm can be obtained from the laser. The laser had a threshold of 4.7 W and a slope efficiency of 12.6% when an output coupler of R = 98% was used.
ACCESSION #
9518415

 

Related Articles

  • Selective Laser Sintering of PZT Ceramic Powders. Gureev, D. M.; Ruzhechko, R. V.; Shishkovskiı, I. V. // Technical Physics Letters;Mar2000, Vol. 26 Issue 3, p262 

    Conditions for the selective laser-induced layer sintering of a stoichiometric mixture of PbO, ZrO[sub 2], and TiO[sub 2] powders with the formation of bulk PZT ceramic articles were studied. The laser processing allows articles of the PZT ceramics to be obtained immediately in the course of...

  • Analysis of electro-active regions and conductivity of BaMnO ceramic by impedance spectroscopy. Hayat, Khizar; Nadeem, M.; Javid Iqbal, M.; Rafiq, M.; Hasan, M. // Applied Physics A: Materials Science & Processing;Jun2014, Vol. 115 Issue 4, p1281 

    Polycrystalline BaMnO ceramic powders were prepared using the conventional mixed oxide route accompanied with several milling processes. Single phase formation was verified by recording the X-ray diffraction pattern of the powder as well as sintered pellet at room temperature. Scanning electron...

  • Characterization of yttrium-Doped Barium Zirconate Nanocrystalline Powder Prepared by Spray Pyrolysis. Muccillo, E. N. S.; Gonçalves, M. D.; Grosso, R. L.; Muccillo, R. // Materials Science Forum;2014, Vol. 798-799, p407 

    Investigation on polycrystalline electroceramics involves the synthesis, the consolidation and the analysis of the electrical behavior, along with careful evaluation of the final microstructure. The synthesis of ceramic powders with controlled characteristics is crucial in the study of materials...

  • Improvement of Signal Stability by a Cyclone-type Particle Separator for Ceramic Analysis using Laser Ablation ICP-MS. Jin Sook Lee; B. Lim, H. // Bulletin of the Korean Chemical Society;2014, Vol. 35 Issue 8, p2555 

    This article presents a stud on a cyclone-type particle separator that was designed to introduce the ablated particles. It discusses the advantages of laser ablation, the signal intensities and the relative standard deviations, and the effect of the separator on the signal intensities of ceramic...

  • Hybrid sol – gel method of obtaining nanostructured yttrium-aluminum garnet powders for laser ceramic. Baranova, G.; Grinberg, E.; Zharikov, E. // Glass & Ceramics;Sep2009, Vol. 66 Issue 9/10, p328 

    The production of finely dispersed yttrium-aluminum garnet (YAG) powder, which is the initial material for ceramics, using as precursors secondary aluminum butylate and a crystal-hydrate salt — yttrium chloride hexahydrate, is examined. It is found that depending on the conditions of...

  • Strong upconversion from Er3Al5O12 ceramic powders prepared by low temperature direct combustion synthesis. Maciel, Glauco S.; Rakov, Nikifor; Fokine, Michael; Carvalho, Isabel C. S.; Pinheiro, Carlos B. // Applied Physics Letters;8/21/2006, Vol. 89 Issue 8, p081109 

    Crystalline ceramic powders of Er3Al5O12 were obtained by low temperature direct combustion synthesis. Irradiating the sample with a low-power continuous-wave infrared (1.48 μm) diode laser led to ultraviolet, violet, blue, green, and red (380, 410, 456, 495, 525, 550, and 660 nm) emissions....

  • Influence of the HPDL surface treatment of the X40CrMoV5-1 tool steel on wear resistance. Jonda, Ewa; Lukaszkowicz, Krzysztof // Advanced Materials Research;2014, Issue 1033-1036, p428 

    The paper presents the effect of alloying with WC and TaC powders on structure and mechanical properties of the X40CrMoV5-1 steel surface layer using the HPDL (High Power Diode Laser). The metallographic investigations on light microscope show that during alloying the X40CrMoV5-1 hot work tool...

  • HPDL laser alloying of Al-Si-Cu alloy with ZrO2 powder. LABISZ, Krzysztof; TAŃSKI, Tomasz; KRUPIŃSKA, Beata; KRUPIŃSKI, Mariusz; PAKIEŁA, Wojciech // Advanced Materials Research;2014, Issue 1033-1036, p434 

    The purpose of this paper was the investigation of laser treatment influence on the microstructure and properties of the surface layer of heat treated Al-Si-Cu cast aluminium alloys, using the high power diode laser (HPDL). The performed laser treatment involves remelting and feeding of ZrO2...

  • Energy Efficient Manufacturing of Power Electronics Substrates Through Selective Laser Melting Technology. Syed-Khaja, Aarief; Stecher, Jonathan; Esfandyari, Alireza; Kreitlein, Sven; Franke, Joerg // Applied Mechanics & Materials;2017, Vol. 856, p188 

    In view of rising energy prices, high-energy consumption, and the associated environmental problems, in recent years the focus was shifted on the demand for energy and resource efficiency in the manufacturing sector. In the context of the project 'PowerSLAM' under Green Factory Bavaria Project,...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics