TITLE

Four-Point Bending Test of Determining Stress-Strain Curves Asymmetric between Tension and Compression

AUTHOR(S)
Kato, H.; Tottori, Y.; Sasaki, K.
PUB. DATE
March 2014
SOURCE
Experimental Mechanics;Mar2014, Vol. 54 Issue 3, p489
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
A method of determining both uniaxial tension and compression stress-strain curves from the result of a single four-point bending test was demonstrated. Stress-strain curves of magnesium showing tension-compression asymmetry due to twinning deformation and those of an S45C steel due to the Bauschinger effect were calculated. The Mayville-Finnie equation was modified slightly for this calculation. The calculation is sensitive to small change in the slope of bending curve, revealing an aspect of inverse problem.
ACCESSION #
94763099

 

Related Articles

  • Effect of Microstructural Banding on the Fatigue Behavior of Induction-Hardened 4140 Steel. Hayne, M.; Anderson, P.; Findley, K.; Tyne, C. // Metallurgical & Materials Transactions. Part A;Aug2013, Vol. 44 Issue 8, p3428 

    The fatigue behavior of induction-hardened calcium-treated 4140 steel with three different case depths was evaluated using rotating bending fatigue tests. The as-received microstructure of the steel was banded and the orientation of microstructural banding with respect to the fatigue specimen...

  • In-Situ Neutron Diffraction Study of the Bauschinger Effect in B2 Structured CoZr. Mulay, R.P.; Clausen, B.; Agnew, S.R. // Metallurgical & Materials Transactions. Part A;Jan2011, Vol. 42 Issue 1, p60 

    combination of in-situ neutron diffraction and elastoplastic self-consistent (EPSC) modeling have been used to elucidate the role played by intergranular stresses in the Bauschinger effect in B2 structured CoZr at room temperature and 423 K (150 °C). It is shown that, when insufficient slip...

  • Springback of Copper Alloy Sheets after U-bending. Hiroshi Hamasaki; Yasuhiro Hattori; Kingo Furukawa; Fusahito Yoshida // Applied Mechanics & Materials;2014, Issue 510, p118 

    Springback after U-bending of Cu-Ni-Si alloy sheet and cold-rolled brass sheets (JIS C2600R-H and C2600R-1/4H) was calculated by using FEM. In the simulations, the Yoshida-Uemori kinematic hardening model was employed, by which stress-strain responses under uniaxial tension and cyclic...

  • Bauschinger effect in unpassivated freestanding thin films. Shishvan, Siamak Soleymani; Nicola, Lucia; Van der Giessen, Erik // Journal of Applied Physics;May2010, Vol. 107 Issue 9, p093529-1 

    Two-dimensional (2D) discrete dislocation plasticity simulations are carried out to investigate the Bauschinger effect (BE) in freestanding thin films. The BE in plastic flow of polycrystalline materials is generally understood to be caused by inhomogeneous deformation during loading, leading to...

  • HOW METAL MOVES.  // Hammer's Blow;Fall2014, Vol. 22 Issue 4, p15 

    The article demonstrates how metal moves through a test piece of a bend without pre-dishing of the material, focusing on the amount of concavity to the outside surface of the bend, along with photographs showing how the material behaves while being bent.

  • Mathematical Simulation of Cramped Bending of Sheet Parts Using Finite Element Analysis. Yeskina, Ye. V.; Gromova, Ye. G. // Key Engineering Materials;2016, Vol. 685, p186 

    The paper describes the method of manufacture of profiles in cramped bending conditions using polyurethane. The scope of studies included stress-strain state of elastic die and parent sheet, as well as the influence of the basic process parameters on characteristics of the produced items using...

  • The bending forming mechanism of copper alloy by different lasers. Suqin Jiang; Aihui Liu; Xiaoxue Wang; Zhong Chen // Advanced Materials Research;2014, Vol. 968, p142 

    By FEA method, the bending of the copper alloy thin-plates by continuous laser forming (CLF) and pulse laser forming (PLF) was studied. Based on the analysis of dynamic change and steady distribution for the fields of temperature, stress/strain and displacement, the forming mechanism and rule of...

  • Application of Weibull distribution to describe S-N curve with using small number specimens. Strzelecki, Przemysław; Tomaszewski, Tomasz // AIP Conference Proceedings;2016, Vol. 1780 Issue 1, p1 

    The paper presents a standard approach to the determination of the S-N curve. It also presents an alternative approach requiring fewer samples. The proposed method was verified based on test results for steel S3555J2+C. The tests were performed by rotating bending. Based on the resulting curves,...

  • Seismic performance of Confined Concrete by Stirrup Spacing. Dogan, Mizam; Kırac, Nevzat // Proceedings of World Academy of Science: Engineering & Technolog;Feb2009 Supplement, Vol. 50, p1332 

    The function of the columns is to resist the floor loads transferred either directly or trough beams. Reinforced concrete columns normally contain longitudinal steel bars considering the possibility of bending, time dependent deformation and settlement. They are confined by lateral reinforcement...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics