TITLE

Assessment of Energy Consumption and Internal Stresses in Surface Layer in the Abrasive Electro-discharge Grinding (AEDG) Process

AUTHOR(S)
Golabczak, Andrzej; Swiecik, Robert
PUB. DATE
February 2013
SOURCE
Defect & Diffusion Forum;2013, Vol. 334-335, following p89
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
In this work, results have been presented related to the influence of selected electrical parameters of the AEDG process on the energy consumption and state of the internal stresses in the outer layer at this stage of the process, in comparison with conventional grinding. The basis of this work has been possible by investigations of the deep grinding of surfaces of the titanium alloy Ti6Al4V with the use of a CBN grinding wheel and sintered carbide S20S with using diamond grinding wheel with metallic binding agent. For the comparative evaluation of the conventional grinding and AEDG, measurements of the specific grinding energy, energy of the spark discharge and internal stresses in the surface layer have been used.
ACCESSION #
94142547

 

Related Articles

  • Experimental investigation on flank wear and tool life, cost analysis and mathematical model in turning hardened steel using coated carbide inserts. Sahooa, Ashok Kumar; Sahoob, Bidyadhar // International Journal of Industrial Engineering Computations;Fall2013, Vol. 4 Issue 1, p571 

    Turning hardened component with PCBN and ceramic inserts have been extensively used recently and replaces traditional grinding operation. The use of inexpensive multilayer coated carbide insert in hard turning is lacking and hence there is a need to investigate the potential and applicability of...

  • Experimental study on fabrication and evaluation of a micro-scale shaft grinding tool. Gong, Y.; Wen, X.; Cheng, J.; Yin, G.; Wang, C. // Journal of Mechanical Science & Technology;Mar2014, Vol. 28 Issue 3, p1027 

    This paper presents a micro-grinding experiment on AISI 1020 steel and Ti-6Al-4V to study micro-grinding principle and the change rule of the force and surface with different grinding parameters. A novel micro shaft grinding tool is fabricated by cold sprayed with CBN grains, the manufacturing...

  • The Theoretical Analysis and Experimental study on the Distribution Characteristics of Motion Parameters In the Process of Honing Gear. Cheng Zhang; Guoxing Liang; Ming Lv; Shiying Wang // Key Engineering Materials;2014, Vol. 620, p225 

    Gear honing processing is a kind of processing method which belongs to the point-contact generating gear finishing. Its movement form is equivalent to a pair of gears transmission which the surface of the gear-honing-tool is adhered a layer of grinding grain. When it works in rolling processing,...

  • An Experimental Investigation on the Grinding Force of the Electroplating CBN Grinding Wheel with Abrasive Ordering Pattern. Shan Zhang; Yushan Lu; Jun Wang; Fei Ma; Zhizhen Liu; Long Xiang // Applied Mechanics & Materials;2014, Vol. 687-691, p534 

    In order to obtain the effects of abrasive configurations on the grinding force of superhard abrasive grinding wheel, an experiment was carried out, which grinds steel material by the use of electroplating CBN grinding wheel with different abrasive configurations, mainly including disordered,...

  • An Experimental Study on Grinding Fir-tree Root Forms Using Vitrified CBN Wheels. Zhongde Shi; Amr Elfizy; Attia, Helmi // Advanced Materials Research;2014, Issue 1017, p55 

    An experimental study was undertaken to explore the conditions and performance on rough and finish grinding fir-tree root forms of turbine blades made of a nickel-based alloy using vitrified CBN wheels and water-based grinding fluid. This work was motivated by switching the grinding of fir-tree...

  • Deep Profiled Slot Grinding on a Nickel-based Alloy with Electroplated CBN Wheels. Zhongde Shi; Elfizy, Amr; Attia, Helmi // Advanced Materials Research;2015, Vol. 806, p3 

    A process for grinding deep profiled slots in a nickel-based alloy with electroplated cubic boron nitride (CBN) wheels and straight oil is presented. These slots were prepared by this process for further grinding with electroplated CBN quills to generate the final fir-tree slots in gas turbine...

  • Comparative study on grinding of thin-walled and honeycomb-structured components with two CBN wheels. Tian, Y.; Zhong, Z.; Rawat, R. // International Journal of Advanced Manufacturing Technology;Nov2015, Vol. 81 Issue 5-8, p1097 

    In the grinding of thin-walled and honeycomb-structured components made up of Hastelloy, undesired burrs are often created. The formed burrs negatively affect the quality of the products. Subsequent deburring increases overall manufacturing process time and cost. This work was focused on...

  • Sandvik makes a case for hard turning to replace grinding. admin // MWP (Online Edition);9/28/2012, p641 

    The article reports that Sandvik Coromant UK is one of the machine shops that has switched from grinding to hard part turning, a move that was encouraged and accelerated by reductions of more than 50% in component costs. The company has been an active partner in offering a broad range of cubic...

  • Investigation of Surface Integrity on TC4-DT in High Speed Grinding with CBN Wheel. Chen Yaoguang; Lu Wenzhuang; Xu Jun; Zhu Yansong; Zuo Dunwen // Advanced Materials Research;2014, Vol. 1027, p140 

    A series of grinding experiments were carried out with CBN wheel to focus on the surface integrity of titanium alloy TC4-DT in high speed grinding. In order to get the proper process parameters to control the surface integrity of the TC4-DT, surface roughness, subsurface morphology and...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics