TITLE

TİKSO-DÖKÜM YÖNTEMİYLE ÜRETİLEN Al2024 ALAŞIMININ MİKROYAPI VE MEKANİK ÖZELLİKLERİNİN İNCELENMESİ

AUTHOR(S)
TANEROĞLU, Hasan; AKAR, Neşet; KILIÇLI, Volkan
PUB. DATE
December 2013
SOURCE
Journal of the Faculty of Engineering & Architecture of Gazi Uni;Dec2013, Vol. 28 Issue 4, p801
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
In this study, a wrought Al2024 aluminum alloy formed with thixocasting method which is one of the semi-solid metal forming processes and the effect of liquid fraction and aging heat treatment (T6) on microstructure an mechanical properties has been investigated. Billets produced by strain induced melt activation (SIMA) process were used in thixocasting. In the semi-solid region, microstructural and mechanical property variations depending on the temperatures that corresponded to different liquid fractions (608 °C, 616 °C, and 619 °C), and 2.37 m/s ram speed have been investigated. In the forming by thixocasting, at the temperature (608 °C) that corresponded to low liquid fraction the die cavity has not been fully filled by the semi-solid billet. The die cavity has been fully filled by semi-solid billet at high liquid fraction (60% and 65%). The mechanical properties of specimens which produced by thixocasting were found to be 45% lower than extruded + T6 condition specimen. The mechanical properties of the specimens which produced by thixocasting + T6 condition are almost same as specimens in extruded conditions.
ACCESSION #
93433021

 

Related Articles

  • Microstructural Homogeneity and Hot Deformation of Various Friction-Stir-Processed 5083 Al Alloys. García-Bernal, M.; Mishra, R.; Hernández-Silva, D.; Sauce-Rangel, V. // Journal of Materials Engineering & Performance;Jan2017, Vol. 26 Issue 1, p460 

    Diverse studies on FSP of 5083 Al alloys have been conducted, and some have made comparisons with previous studies of similar alloys, but many times such comparisons could be invalid because of differences in the parameters used during FSP, above all, tool profile. Five 5083 Al alloys produced...

  • Twin-roll Casting of High-strength Age-hardened Aluminium Alloys. Grydin, O.; Schaper, M.; Danchenko, V. // Metallurgical & Mining Industry;2011, Vol. 3 Issue 7, p7 

    By experimental investigations on twin-roll casting of high-strength age-hardened aluminum alloys EN AW-6082 and EN AW-7020 optimal process parameters, which provide a stable and continuous formation of medium thickness strips on the full roll width with a good surface quality, were determined....

  • Three-Point Bending of Heat-Treatable Aluminum Alloys: Influence of Microstructure and Texture on Bendability and Fracture Behavior. Westermann, Ida; Snilsberg, Knut; Sharifi, Zeinab; Hopperstad, Odd; Marthinsen, Knut; Holmedal, Bjørn // Metallurgical & Materials Transactions. Part A;Nov2011, Vol. 42 Issue 11, p3386 

    Three-point bending tests of extruded aluminum alloys showed lower bendability when the bending axis is aligned with the extrusion direction compared to the transverse direction. In the present work, three different microstructures of a commercial AA7108 aluminum alloy were studied with respect...

  • Effect of heat treatment on microstructure and microhardness evolution in a Ti-6Al-4V alloy processed by high-pressure torsion. Wang, Ying; Langdon, Terence // Journal of Materials Science;Jul2013, Vol. 48 Issue 13, p4646 

    A Ti-6Al-4V alloy was heat-treated to give two types of microstructures with different volume fraction of equiaxed α phase and lamellar (α + β) microstructure. Disks were cut from the heat-treated rods and processed by quasi-constrained high-pressure torsion (HPT) at room temperature...

  • Constitutive Modeling of Hot Deformation Behavior of the AA6063 Alloy with Different Precipitates. Anjabin, Nozar; Taheri, Ali Karimi; Kim, Hyoung Seop // Metallurgical & Materials Transactions. Part A;Dec2013, Vol. 44 Issue 12, p5853 

    The current study proposes a simple constitutive model that integrates the kinetics of precipitation during static aging and the kinetics of precipitate dissolution during preheating to deformation temperature to predict the hot flow behavior of AA6063 alloy. The model relates the flow behavior...

  • Formation of micrograin structure and superplastic state in alloys of the Al-Cu-Mg-Fe-Ni system. Kotov, A.; Mikhailovskaya, A.; Portnoi, V.; Sagalova, T. // Metal Science & Heat Treatment;Nov2012, Vol. 54 Issue 7/8, p340 

    The methods of light and scanning electron microscopy and x-ray phase and thermal analysis are used to study the effect of the special features of the production process on the characteristics of the grain structure and super-elasticity of sheets from alloys based on the Al - Cu - Mg - Fe - Ni...

  • Experimental and Numerical Analysis on the Formability of a Heat-Treated AA1100 Aluminum Alloy Sheet. Durán, Alicia; Signorelli, Javier; Celentano, Diego; Cruchaga, Marcela; François, Manuel // Journal of Materials Engineering & Performance;Oct2015, Vol. 24 Issue 10, p4156 

    The objective of this work is to experimentally and numerically determine the influence of plastic anisotropy on the forming limit curve (FLC) for a heat-treated (300 °C-1 h) AA1100 aluminum alloy sheet. The FLCs were obtained by the Nakajima test, where the anisotropy effect on the FLC was...

  • The Influence of Prior Natural Aging on the Subsequent Artificial Aging Response of Aluminium Alloy A356 with Respective Globular and Dendritic Microstructures. Möer, Heinrich; Govender, Gonasagren; Rossouw, Pierre; Stumpf, Waldo // Advances in Materials Science & Engineering;2011, p1 

    Alloy A356 is one of the most popular alloys used for semisolid metal forming. The heat treatment cycles that are currently applied to semisolid processed components are mostly those that are in use for dendritic casting alloys. The assumption has been made that these heat treatments are not...

  • Mechanical Behavior of Ultrafine-Grained Cryomilled Al 5083 at Elevated Temperature. Witkin, David; Han, Bing Q.; Lavernia, Enrique J. // Journal of Materials Engineering & Performance;Aug2005, Vol. 14 Issue 4, p519 

    The mechanical behavior of cryomilled and consolidated Al 5083 with a duplex ultrafine-grained microstructure is described for compression testing at different temperatures and strain rates. The relationship among flow stress, strain rate, and testing temperature provides an initial hotworking...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics