TITLE

Partial Transient Liquid-Phase Bonding, Part I: A Novel Selection Procedure for Determining Ideal Interlayer Combinations, Validated Against Al2O3 PTLP Bonding Experience

AUTHOR(S)
Cook III, Grant O.; Sorensen, Carl D.
PUB. DATE
December 2013
SOURCE
Metallurgical & Materials Transactions. Part A;Dec2013, Vol. 44 Issue 12, p5732
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Partial transient liquid-phase (PTLP) bonding is a bonding process that can bond hard-to-join materials, such as ceramics. The process uses a multi-layer interlayer composed of a thick refractory core and thin diffusant layers on each side. Upon heating, the diffusant material melts, and diffusion occurs until the liquid isothermally solidifies. Selecting interlayer materials is a key problem in producing strong, reliable PTLP bonds; materials are usually selected empirically or system by system. This article presents a novel selection procedure that provides a generalized, comprehensive, first-principles-based approach. Components of the selection procedure are linked directly to key characteristics of PTLP bonding. A filtering routine that provides structure for the selection procedure is summarized in this article and detailed in a companion article. Specific capabilities of the routine, such as non-symmetric bonds, add to its effectiveness in identifying additional PTLP bond candidates. By way of example, output from the selection procedure, in conjunction with sessile drop data, is used to analyze all Al 2O 3 PTLP bonds in the current literature. All analyzed bonds are included in various outputs from the selection procedure, validating its comprehensiveness. Also, Al 2O 3 PTLP bonds are analyzed as a whole, leading to the identification of important trends that result in increased bond strength. Finally, additional interlayer combinations for PTLP bonding of Al 2O 3 are presented based on output from the selection procedure and existing sessile drop data.
ACCESSION #
91988918

 

Related Articles

  • Gauging friction.  // Machine Design;11/18/2010, Vol. 82 Issue 20, p44 

    Two charts are presented which depict two tests conducted to determine the difference of speed and pressure between U-seals and other friction-modified hydraulic seals such as the HL seal.

  • Metal/ceramic laminar composite immersion heater for heating Hot Dip Galvanizing Zinc Kettle. Ruina Ma; Xiaoming Cao; An Du; Adrew Herd; Chunduo Dai // Applied Mechanics & Materials;2014, Issue 665, p90 

    A new type of laminar composite material has been developed by the bonding of ceramic and metal with a special agglutinate metal. A tube can be made of the laminar composite material and this tube can perform as an outer sheath of an immersion heater. Such heaters can be made to lager size and...

  • Bonding rubber to metal.  // Machine Design;11/17/2005, Vol. 77 Issue 22, p44 

    Focuses on improvements made by engineers at Ashtabula Rubber Co. in the process of bonding rubber components to metals. Benefits offered by the bonding process develop by the engineers.

  • Vacuum Diffusion Bonding of Flange-foils for X-ray Windows. Avagyan, Vardan; Mikaelyan, Rafael; Petrosyan, Artush // AIP Conference Proceedings;2007, Vol. 879 Issue 1, p1046 

    A vacuum diffusion technology for flange-foil bonding with prevention of the foil oxidation is presented. The application of the technology for the X-ray windows with copper, stainless steel, titan and beryllium foils is discussed. The experimental results for stainless steel-titanium X-ray...

  • High sensitivity plasmonic index sensor using slablike gold nanoring arrays. Chia-Yang Tsai; Shao-Ping Lu; Jyun-Wei Lin; Po-Tsung Lee // Applied Physics Letters;4/11/2011, Vol. 98 Issue 15, p153108 

    We investigate the index sensing characteristics of plasmonic arrays based on square lattice slablike gold nanorings (NRs) with different ring widths. The gold NR arrays exhibit two extinction peaks in the visible and near-infrared corresponding to antibonding and bonding modes. Redshift and...

  • Diffusion soldering using a Gallium metallic paste as solder alloy: study of the phase formation systematics. Sommadossi, Silvana; Troiani, Horacio E.; Fernández Guillermet, Armando // Journal of Materials Science;Dec2007, Vol. 42 Issue 23, p9707 

    In this work preliminary results are reported on the characterization of Pb-free joints produced by using a diffusion soldering method at a process temperature of 700 °C during 20 min. The solder alloy is a metallic paste involving Ga and Al and Ni powder, and the substrates are Cu and Ni....

  • A Study of Transient Liquid-Phase Bonding of Ag-Cu Using Differential Scanning Calorimetry. Kuntz, M. L.; Zhou, Y.; Corbin, S. F. // Metallurgical & Materials Transactions. Part A;Aug2006, Vol. 37 Issue 8, p2493 

    A novel approach using differential scanning calorimetry (DSC) to quantify interface kinetics in a solid/liquid diffusion couple is applied to characterize the isothermal solidification stage during transient liquid-phase (TLP) bonding of Ag and Cu using a Ag-Cu interlayer. When the DSC results...

  • Analysis of Microstructural Changes Induced by Linear Friction Welding in a Nickel-Base Superalloy. Ola, O.T.; Ojo, O.A.; Wanjara, P.; Chaturvedi, M.C. // Metallurgical & Materials Transactions. Part A;Dec2011, Vol. 42 Issue 12, p3761 

    A detailed microstructural analysis was performed on a difficult-to-weld nickel-base superalloy, IN 738, subjected to linear friction welding and Gleeble thermomechanical simulation, to understand the microstructural changes induced in the material. Correlations between the microstructures of...

  • Microstructural Evolution and Bonding Behavior during Transient Liquid-Phase Bonding of a Duplex Stainless Steel using two Different Ni-B-Based Filler Materials. Yuan, Xinjian; Kim, Myung; Kang, Chung // Metallurgical & Materials Transactions. Part A;May2011, Vol. 42 Issue 5, p1310 

    Microstructural evolution and bonding behavior of transient liquid-phase (TLP) bonded joint for a duplex stainless steel using MBF-30 (Ni -4.5Si -3.2B [wt pct]) and MBF-50 (Ni -7.5Si -1.4B -18.5Cr [wt pct]) were investigated. Using MBF-30, the microstructure of the athermally solidified zone was...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics