TITLE

Influence of Secondary Cyclic Hardening on the Low Cycle Fatigue Behavior of Nitrogen Alloyed 316LN Stainless Steel

AUTHOR(S)
Prasad Reddy, G. V.; Sandhya, R.; Mathew, M. D.; Sankaran, S.
PUB. DATE
December 2013
SOURCE
Metallurgical & Materials Transactions. Part A;Dec2013, Vol. 44 Issue 12, p5625
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
In this article, the occurrence of secondary cyclic hardening (SCH) and its effect on high-temperature cyclic deformation and fatigue life of 316LN Stainless steel are presented. SCH is found to result from planar slip mode of deformation and enhance the degree of hardening over and above that resulted from dynamic strain aging. The occurrence of SCH is strongly governed by the applied strain amplitude, test temperature, and the nitrogen content in the 316LN SS. Under certain test conditions, SCH is noticed to decrease the low cycle fatigue life with the increasing nitrogen content.
ACCESSION #
91988616

 

Related Articles

  • Distortion Analysis in the Manufacturing of Cold-Drawn and Induction-Hardened Components. Hirsch, Thomas Georg Karl; da Silva Rocha, Alexandre; Menezes Nunes, Rafael // Metallurgical & Materials Transactions. Part A;Dec2013, Vol. 44 Issue 12, p5806 

    In this investigation, a design of experiments analysis of distortion for a typical manufacturing process involving pre-straightening, cold drawing, and induction hardening of AISI 1045 cylindrical steel bars was carried out. A careful characterization of the material, including residual stress...

  • Modeling of Microindentation with Consideration of the Surface Roughness. Chuah, Hun Guan; Ripin, Zaidi Mohd // Metallurgical & Materials Transactions. Part A;Dec2013, Vol. 44 Issue 12, p5676 

    A finite element model of a microindentation is developed where the scanned surface topography data which represent the actual surface-roughness values are used in the construction of the finite element model of the workpiece. Indentation simulation with friction effect solely due to the surface...

  • Microstructural Investigations of Ultra-High Performance Concrete Obtained by Pressure Application within the First 24 Hours of Hardening. Justs, Janis; Bajare, Diana; Korjakins, Aleksandrs; Mezinskis, Gundars; Locs, Janis; Bumanis, Girts // Construction Science;2013, Vol. 14, p50 

    In this study, the effect of pressure application (0–50 MPa) to fresh concrete right after casting and during the first 24 hours of hardening has been examined. Supplementary cementitious materials in a form of silica fume, nanosilica and ground quartz sand were used. The aim of pressure...

  • Concept Validation for Selective Heating and Press Hardening of Automotive Safety Components with Tailored Properties. Nan Li; Jianguo Lin; Dean, Trevor A.; Dry, Damian; Balint, Daniel // Key Engineering Materials;2014, Vol. 622-623, p1124 

    A new strategy termed selective heating and press hardening, for hot stamping of boron steel parts with tailored properties is proposed in this paper. Feasibility studies were carried out through a specially designed experimental programme. The main aim was to validate the strategy and...

  • FORMATION OF FINE STRUCTURE OF DIFFERENTIALLY HARDENED RAILS. Gromov, V. E.; Ivanov, Yu. F.; Morozov, K. V.; Alsaraeva, K. V. // Applied Mechanics & Materials;2014, Issue 682, p41 

    Differential hardening of rails by compressed air at different regimes is accompanied by formation of morphologically different structure, being formed according to the diffusion mechanism of γ ↔ α transformation and consisting of grains of lamellar pearlite, free ferrite and grains...

  • Friction Stir Processing on Carbon Steel. Tarasov, Sergei Yu.; Melnikov, Alexander G.; Rubtsov, Valery E. // AIP Conference Proceedings;2014, Vol. 1623, p627 

    Friction stir processing of medium carbon steel samples has been carried out using a milling machine and tools made of cemented tungsten carbide. Samples have been machined from 40 and 40X steels. The tools have been made in the shape of 5×5×1.5 mm and 3×3×1.5 mm tetrahedrons....

  • Fatigue behaviour of commercially pure aluminium processed by rotary swaging. Abdulstaar, Mustafa A.; Mhaede, Mansour; Wollmann, Manfred; Wagner, Lothar // Journal of Materials Science;Feb2014, Vol. 49 Issue 3, p1138 

    Fatigue strength of ultrafine-grained commercially pure aluminium (Al 1050) produced by severe plastic deformation (rotary swaging) was investigated. Fatigue tests were carried out on smooth and notched specimens. Results show improved static and fatigue strength of the rotary swaging processed...

  • The Effect of Hydrogen on Fatigue Properties of Metals used for Fuel Cell System. Murakami, Y. // International Journal of Fracture;Mar2006, Vol. 138 Issue 1-4, p167 

    The effect of hydrogen on the fatigue properties of alloys which are used in fuel cell (FC) systems has been investigated. In a typical FC system, various alloys are used in hydrogen environments and are subjected to cyclic loading due to pressurization, mechanical vibrations, etc. The materials...

  • Influence of Heat Treatment with Heating in the Intercritical Temperature Range on the Properties of Steels 60C2A and 60C2XФA. Malinov, L. S.; Malysheva, I. E.; Mali, D. V. // Metallurgical & Mining Industry;2012, Vol. 4 Issue 1, p27 

    Data on the influence of heat treatment with heating in the intercritical temperature range on the properties of steels 60C2A and 60C2AФА providing production in them multiphase structures with metastable retained austenite are presented.

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics