TITLE

Effect of Cold Spraying Parameters and Their Interaction an Hydroxyapatite Deposition

AUTHOR(S)
Singh, R. P.; Batra, U.
PUB. DATE
October 2013
SOURCE
Journal of Applied Fluid Mechanics;Oct2013, Vol. 6 Issue 4, p555
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Cold spraying has been effectively investigated for spraying of various metals, alloys and composites. Coating of bio-ceramics like Hydroxyapatite (HAP) using thermal spraying has been investigated extensively, but there is a dearth of research related with HAP deposition using cold spraying. The relative percentage contribution of five important cold spraying parameters, their optimum combination and expected HAP particle velocity at optimum combination have been extensively discussed by the author, but no researcher reported the interactional effect of cold spraying parameters on HAP particle velocity. This paper examined the severity index of interactional effect of five important factors of cold spraying viz. gas type, gas inlet pressure, gas inlet temperature, particle size and particle temperature on HAP particle velocity. Most influential factor pairs and their influence on HAP particle velocity have been discussed with respect to various cold spraying gases viz. air, hydrogen, nitrogen and helium. In addition, CFD gas pressure and temperature distributions along the nozzle length and their mathematical validation have also been undertaken in the present paper.
ACCESSION #
91956077

 

Related Articles

  • Practical Comparison of Cylindrical Nozzle and De Laval Nozzle for Wire Arc Spraying. Matz, Marc-Manuel; Aumiller, Markus // Journal of Thermal Spray Technology;Dec2014, Vol. 23 Issue 8, p1470 

    In this article, two different nozzle designs (cylindrical nozzle and de Laval nozzle) are compared for use in wire arc spraying. The choice of nozzle is of particular importance because its geometry has a significant influence on the spraying result. The materials used for spraying are steel...

  • A Three-Dimensional Analysis of the Suspension Plasma Spray Impinging on a Flat Substrate. Jadidi, M.; Mousavi, M.; Moghtadernejad, S.; Dolatabadi, A. // Journal of Thermal Spray Technology;Jan2015, Vol. 24 Issue 1/2, p11 

    Suspension feedstock in plasma spraying is an emerging process for producing coatings with enhanced characteristics. Sub-micron up to few micron-sized particles are suspended in a liquid and injected into the plasma plume. After suspension's breakup and evaporation, molten and semi-molten fine...

  • Coaxial air flow device for the production of millimeter-sized spherical hydrogel particles. Workamp, Marcel; Alaie, Sepideh; Dijksman, Joshua A. // Review of Scientific Instruments;Dec2016, Vol. 87 Issue 12, p1 

    We describe a method to produce millimeter-sized hydrogel particles, by dispersing aqueous droplets in an oil using a nozzle and subsequently solidifying them. We show that we can vary the size of the particles using an air flow along the nozzle. The resulting particle size can be well predicted...

  • Synthesis and characterization of an experimental Zn-hydroxyapatite powders with application in dentistry. Prodan, Doina; Moldovan, Marioara; Prejmerean, Cristina; Silaghi- Dumitrescu, Laura; Boboia, Stanca; Popescu, Violeta; Pascalau, Violeta; Molea, Andreia; Diana, Lazar; Perhaiţa, Ioana // Key Engineering Materials;2014, Vol. 587, p43 

    In the present study, ZnO-hydroxyapatite (HA-Zn) was synthesized, thermally treated at different temperatures and then characterized. The HA-Zn powder was characterized mainly by FTIR and XRD, but have been performed investigations like SEM, BET and size distribution. The addition of ZnO in...

  • The influence of high velocity thermal spraying methods on top surface topography of WC-Co coatings. Myalska, Hanna; Wieczorek, Jakub; Szymański, Krzysztof; Moskal, Grzegorz // Solid State Phenomena;2014, Vol. 226, p149 

    Characterization of top surfaces of WC-Co coatings obtained during deposition process of high velocity thermal spraying type was showed in this article. The feedstock powder was so called "superfine" powder of WC-17Co types produced by Inframat. In first part of article short characterization of...

  • Tomographic Particle Localization and Velocity Measurement. Kirner, S.; Forster, G.; Schein, J. // Journal of Thermal Spray Technology;Jan2015, Vol. 24 Issue 1/2, p38 

    Wire arc spraying is one of the most common and elementary thermal spray processes. Due to its easy handling, high deposition rate, and relative low process costs, it is a frequently used coating technology for the production of wear and corrosion resistant coatings. In order to produce reliable...

  • The HL-60 Cells Response to Various Particle Sizes of Tetracalcium Phosphate Ceramic Delivery System. Benghuzzi, Hamed; Tucci, Michelle // Key Engineering Materials;2017, Vol. 720, p77 

    The specific objective of this investigation is to study the effect of tetracalcium phosphate (TeCP) delivery system fabricated from three different particle sizes (<38, 45 and 75 um) on the viability of HL-60 cell line in culture. Each TeCP reservoir was fabricated using standard protocols. The...

  • Effects of Laser Sintering processing time and temperature on changes in polyamide 12 powder particle size, shape and distribution. Mielicki, C.; Gronhoff, B.; Wortberg, J. // AIP Conference Proceedings;2014, Vol. 1593, p728 

    In laser sintering (LS) un-molten Polyamide 12 (PA12) powder is usually re-used (recycled) in further processes. However, LS processing time at powder bed temperature leads to material property changes. As a consequence, un-molten PA12 powder that is re-used or recycled in further processes...

  • Ultrafine Particles Emitted by Flame and Electric Arc Guns for Thermal Spraying of Metals. Bémer, Denis; Régnier, Roland; Subra, Isabelle; Sutter, Benjamin; Lecler, Marie T.; Morele, Yves // Annals of Occupational Hygiene;Aug2010, Vol. 54 Issue 6, p607 

    The ultrafine aerosol emitted by thermal spraying of metals using flame and electric arc processes has been characterized in terms of particle size distribution and emission rates based on both particle number and mass. Thermal spraying of Zn, Zn/Al, and Al was studied. Measurements taken using...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics