TITLE

Research on flow stress model and dynamic recrystallization model of X12CrMoWVNbN10-1-1 steel

AUTHOR(S)
Sui, Da-shan; Wang, Wei; Fu, Bo; Cui, Zhen-shan
PUB. DATE
May 2013
SOURCE
AIP Conference Proceedings;May2013, Vol. 1532 Issue 1, p826
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Plastic deformation behavior of X12CrMoWVNbN10-1-1 ferrite heat-resistant steel was studied systematically at high temperature. The stress-strain curves were measured at the temperature of 950°C-1250°C and strain rate of 0.0005s-1-0.1s-1 by Gleeble thermo-mechanical simulator. The flow stress model and dynamic recrystallization model were established based on Laasraoui two-stage model. The activation energy was calculated and the parameters were determined accordingly based on the experimental results and Sellars creep equation. The verification was performed to prove the models and it indicated the calculated results were identical to the experimental data.
ACCESSION #
87656177

 

Related Articles

  • Effect of Mo Addition on Strength of Fire-Resistant Steel at Elevated Temperature. Wan, Rongchun; Sun, Feng; Zhang, Lanting; Shan, Aidang // Journal of Materials Engineering & Performance;Aug2014, Vol. 23 Issue 8, p2780 

    A series of Fe-Mo-C steels with Mo addition from 0.1 to 0.8 wt.% has been prepared for studying the effect of Mo on the elevated-temperature strength of fire-resistant steel. Two heat treatments were performed for obtaining either ferrite microstructure or ferrite-bainite microstructure to study...

  • THE FLOW STRESS BEHAVIOR OF SCM435 STEEL UNDER HOT COMPRESSION. Dang XU; Miao-yong ZHU; Zheng-you TANG; Cheng JI // Metalurgia International;2013 Special Issue Nr. 3, Vol. 18, preceding p5 

    No abstract available.

  • The plasticity induced by recrystallization. Éstrin, E. // Doklady Physics;Mar2006, Vol. 51 Issue 3, p125 

    The article presents information on plasticity associated with high-temperature phase transformations. In the absence of applied stresses, the defects during recrystallization occurs randomly in all directions. Thus, the recrystallization should give rise to strains along the direction of...

  • High Temperature Straining Behaviour Of High FeSi Electrical Steel By Torsion Tests. Calvillo, P. R.; García, N. Lasa; Houbaert, Y. // AIP Conference Proceedings;2007, Vol. 907 Issue 1, p451 

    Steel with an increased Si-content has better magnetic properties in electrical applications in terms of high electrical resistivity, reduced energy losses and low magnetostriction. Nevertheless, the oxygen affinity of this element at high working temperatures and the poor ductility observed at...

  • The Network Prediction of Hot Temperature Flow Stress and Dynamic Recrystallization of AZ61 Alloy. Quan Li; Wenjun Liu; Renju Cheng; Cheng Li; Shan Jiang; Suqin Luo; Xianquan Jiang; Fusheng Pan // Advanced Materials Research;7/24/2014, Vol. 989-994, p544 

    In this paper, the Back-Propagation neural network (BP network) and the establishment of the AZ61 magnesium alloy high temperature constitutive model and test data obtained for training the neural network, after training the neural network to become a knowledge-based constitutive model formed...

  • On the causes of formation of non-optimal structures in a pressure-treated low-carbon steel. Valuev, D. V.; Danilov, V. I.; Ivanov, Yu. F. // Russian Physics Journal;Oct2007, Vol. 50 Issue 10, p964 

    An electron microscopy investigation of structural-phase and stress-strained state of a hot-forged material workpiece is performed. It is found out that the scalar dislocation density in ferrite grains and ferrite interlayers of pearlite of steel from the forged piece fractured after...

  • The Strain-Hardening Behavior of Partially Austenitized and the Austempered Ductile Irons with Dual Matrix Structures. Kilicli, Volkan; Erdogan, Mehmet // Journal of Materials Engineering & Performance;Apr2008, Vol. 17 Issue 2, p240 

    In the current study, an unalloyed ductile iron containing 3.50 C wt.%, 2.63 Si wt.%, 0.318 Mn wt.%, and 0.047 Mg wt.% was intercritically austenitized (partially austenitized) in two-phase regions (α + γ) at different temperatures for 20 min and then was quenched into salt bath held at...

  • Advances in local mechanoelectrochemistry for detecting pitting corrosion in duplex steels. Mary, N.; Oltra, R.; Vignal, V.; Coudreuse, L. // Journal of Materials Research;Dec2004, Vol. 19 Issue 12, p3688 

    The goal of this study was to demonstrate that a relationship exists between surface stress and pitting corrosion. The surface stress field generated by polishing was first calculated using a thermomechanical model and a finite element code. Pitting corrosion tests performed at the microscale...

  • Dynamic amorphization and recrystallization of metals in kinetic spray process. Xiong, Yuming; Kang, Kicheol; Bae, Gyuyeol; Yoon, Sanghoon; Lee, Changhee // Applied Physics Letters;5/12/2008, Vol. 92 Issue 19, p193501 

    We reported dynamic amorphization and recrystallization processes of metals upon impact of micron-scaled particles at a high strain rate (109 s-1) combining adiabatic heating with rapid cooling (1010 K s-1) in a kinetic spray process. At the interface of the particle/substrate, an amorphous zone...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics