TITLE

Research on work roll thermal crown in cold rolling mill

AUTHOR(S)
Song, Lei; Shen, Mingang; Chen, Xuebo; Wang, Junsheng
PUB. DATE
May 2013
SOURCE
AIP Conference Proceedings;May2013, Vol. 1532 Issue 1, p1125
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The factors which have influence on the work roll thermal crown in cold strip rolling are discussed. The heat transferring in three directions (radial axis and circumference) were considered for calculating the work roll thermal deformation. Therefore, it is a three dimensions unstable system for the work roll temperature calculation. The plastic deformation work and friction heat are calculated by the divided element and digital integration method. The simplified calculation model is built for the heat transferring along work roll. There are four zones for work roll heat transferring: roll gap zone air cooling zone emulsion zone rolls contact zone. The heat transferring between the zones is decided by the temperature difference. The inter temperature field and thermal deformation of work roll can be calculated by two-dimension finite difference method. The work roll temperature and thermal crown of actual application cold rolling mill are analyzed by the model. By the comparison between calculated values and measured values, the work roll thermal calculation model can meet the accuracy requirement of on-line control.
ACCESSION #
87656165

 

Related Articles

  • FEM analysis of profile control capability during rolling in a 6-high CVC cold rolling mill. Kezhi Linghu; Zhengyi Jiang; Fei Li; Jingwei Zhao; Meng Yu; Yongqiang Wang // Advanced Materials Research;2014, Vol. 988, p257 

    A 3D elastic-plastic finite element method (FEM) model of cold strip rolling for 6-high continuous variable crown (CVC) rolling mill was developed. The rolling force distributions were obtained by the internal iteration processes. The calculated error has been significantly reduced by the...

  • Study of Strain-Induced Change in Structural Characteristics and Long- Range Order in Ni3Al Alloy. Starenchenko, Svetlana; Starenchenko, Vladimir // Advanced Materials Research;2014, Issue 1013, p31 

    In this paper the study of structural characteristics of the coarse-crystalline Ni3Al alloy deformed by cold-rolling at a room temperature is presented. The research was carried out by the Xray methods. It is established that plastic deformation leads to an increase in lattice strain, causes...

  • Simplified Model for Ground Heat Transfer from Slab-on-Grade Buildings. Kissock, Kelly; Selvacanabady, Abinesh; Raghavan, Narendran // ASHRAE Transactions;2013, Vol. 119 Issue 2, p456 

    This paper presents a simplified method to calculate heat loss from slab-on-grade buildings. To develop a simplified method, a transient finite-difference model for heat loss from slab-on-grade buildings was developed. Based on results from the finite difference model, a simplified model of heat...

  • Slip Line Field Solution for Second Pass in Lubricated 4-High Reversing Cold Rolling Sheet Mill. Oluwole, Oluleke O.; Olaogun, Olayinka // Engineering;Dec2011, Vol. 3 Issue 12, p1225 

    The development of a possible slip line field (slf) for theoretical calculations of the deforming pressure (load) in a second pass of a lubricated cold rolling sheet mill and validation using values from an aluminium sheet rolling mill was done in this work. This will be relevant in the...

  • Analysis of the plasticity margin in a rolling site. Ploskov, N.; Danilov, V.; Zuev, L.; Bolotina, I.; Orlova, D. // Russian Physics Journal;May2012, Vol. 54 Issue 12, p1389 

    A stress-deformed state of zirconium alloy in a cold rolling site is investigated considering the process of evolution of localized deformation autowaves and changes in the ultrasound velocity. It is established that transition from the upsetting to reduction region is accompanied by significant...

  • Influence of plastic deformation on the precipitation of Cr in copper. Chbihi, A.; Sauvage, X.; Blavette, D. // Journal of Materials Science;Sep2014, Vol. 49 Issue 18, p6240 

    The effect of cold rolling on the early-stage precipitation mechanisms of Cr in fcc Cu has been investigated using transmission electron microscopy and atom-probe tomography. The results clearly show that the deformation leads to an acceleration of both the precipitation and coarsening kinetics....

  • Supplementary Setting of Target Flatness Curves for 1450 Strip Cold Rolling Mill. Hai Zhou; Jinlan Bai // Applied Mechanics & Materials;2014, Issue 630-642, p800 

    In this paper, for the original target flatness curves of flatness control system of a 1450 cold rolling mill can't satisfy the actual production, parameter setting method is adopted to the supplementary setting of target flatness curves. Based on the analysis of the several common forms of...

  • RESEARCH ON ELECTROMAGNETIC INDUCTIVE MEASUREMENT METHOD FOR COLD-ROLLING STRIP CENTERING CONTROL. Qi Ouyang; Song Peng; Jianping Hu; Wanhong Li; Liming Zhao // Metalurgia International;Jul2012, Vol. 17 Issue 7, p101 

    In the cold rolling mill, CPC (Center Position Control) system is an effective strip guide in the continuous processing line of the strip to maintain the line steady. To compensate lateral reflection of strip in the processing line, an inductive sensor system in a CPC system was operated as a...

  • ANALYSIS AND CONTROL OF CHATTER MARKS OF STRIP STEEL ON HC COLD ROLLING MILL. Chang-Gui Xie; Zhi-Jiang Xie; Ping Chen // Metalurgia International;Apr2012, Vol. 17 Issue 4, p57 

    According to the chatter marks on strip steel of HC cold rolling mill, by adopting continuous tracking measurement and analyzing the collected vibration and simulation analysis on rolling mill, it is found that chatter marks of strip steel surface caused by the Seventh-order natural frequency....

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics