TITLE

2D-FEM analysis of rolls temperature field in induction heating process

AUTHOR(S)
Cai, Ban; Wang, Hao; Mei, Ruibin; Li, Changsheng
PUB. DATE
May 2013
SOURCE
AIP Conference Proceedings;May2013, Vol. 1532 Issue 1, p977
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Hot-roller warm rolling process is expected to achieve a breakthrough in solving the problem of high quality rolling for difficult deformed metals. In this paper roll surface induction heating was studied based on the finite element theory of electromagnetic-thermal coupling and experiment. The law of temperature field for a static roll in induction heating process was analyzed by FEM. The results show that roll surface temperature can achieve 721°C at 48s under 20000Hz power frequency, 350×104A/m2 current density, due to the skin effect on roll surface. Using a special induction coil in the laboratory, an experiment of roll induction heating was carried out with the same process parameters. The calculated results of temperature on roll surface agree well with the measured value.
ACCESSION #
87656142

 

Related Articles

  • Study on the influence of temperature on the surface asperity in micro cross wedge rolling. Lu, H. N.; Wei, D. B.; Jiang, Z. Y.; Wu, D.; Zhao, X. M. // AIP Conference Proceedings;May2013, Vol. 1532 Issue 1, p1032 

    When the common deformation processes are scaled down to micro/meso dimensions, size effect is the particular phenomena in microforming, which is related to the dominant influence of single grains inside the micropart. The conventional cross wedge rolling (CWR) is introduced into the micro scale...

  • Finite Element Modeling of Frictional and Material Anisotropy During Forming of Steel Cylindrical Cups. TRZEPIECIŃSKI, Tomasz; BAZAN, Anna; LEMU, Hirpa G. // Applied Mechanics & Materials;2015, Vol. 789-790, p3 

    The article presents a method of determining the anisotropic friction model in metal forming using multilayer artificial neural networks based on experimental data obtained from the pin-on-disk tribometer. The experimental results show that the friction coefficient depends on the measured angle...

  • Analysis of Inductive Heating and Current Density in Cylindrical Pieces Submitted Cleating Process at a Frequency of 1500Hz. Stasac, Claudia Olimpia; Hoble, Dorel Anton // Journal of Electrical & Electronics Engineering;May2012, Vol. 5 Issue 1, p237 

    The topic of the paper is focused on a study which refers to the distribution of the electromagnetic field in structures made of two materials subject to the process of heating by inductive methods. The study presented in the paper is meant to be a first stage of a more complex one with regard...

  • Thermomechanical Behavior of Work Rolls During Warm Strip Rolling. Khalili, L.; Serajzadeh, S.; Koohbor, B. // Metallurgical & Materials Transactions. Part B;Dec2012, Vol. 43 Issue 6, p1638 

    A mathematical model was developed to assess thermomechanical behavior of work rolls during warm rolling processes. A combined finite element analysis-slab method was first developed to determine thermal and mechanical responses of the strip being rolled under steady-state conditions, and then,...

  • STEEL BALLS FORMING BY CROSS ROLLING WITH UPSETTING. PATER, Z.; TOFIL, A.; TOMCZAK, J. // Metalurgija;2013, Vol. 52 Issue 1, p103 

    The paper describes a process of forming four balls with a diameter of 22 mm by means of cross rolling with upsetting. The paper also presents the tool used to form semi-finished balls. Owing to the application of the finite element method (FEM), the course of the rolling process as well as...

  • UBET-Based Numerical Modeling of Bulk Deformation Processes. Ranatunga, Vipul; Gunasekera, Jay S. // Journal of Materials Engineering & Performance;Feb2006, Vol. 15 Issue 1, p47 

    The paper summarizes the development of numerical procedures for modeling bulk deformation process and preform designing techniques based on the upper bound elemental technique (UBET). UBET has a unique place where an approximate, but faster solution is needed for decision making. In designing...

  • Realistic Modelling of the Tool Kinematics of Radial-Axial Ring Rolling Machines in Finite Element Simulation. Schwich, Gideon; Jenkouk, Vahid; Hirt, Gerhard // AIP Conference Proceedings;2016, Vol. 1769 Issue 1, p1 

    For simulating metal forming processes by means of Finite Element programs it is required to define all tool motions beforehand. This is one of the major difficulties of the conventional Finite Elements Analysis (FEA) for simulating ring rolling processes, since in reality the motions are...

  • Numerical Investigation into the Effect of Uniaxial and Biaxial Pre-Strain on Forming Limit Diagram of 5083 Aluminum Alloy. Zhalehfar, F.; Hosseinipour, S. J.; Nourouzi, S.; Gorji, A. H. // AIP Conference Proceedings;8/22/2011, Vol. 1383 Issue 1, p165 

    In this paper, numerical simulations are carried out to determine the forming limit diagram (FLD) of 5083 aluminum alloy. The aim is to predict the effect of strain path change on the forming limit curve (FLC) of this alloy. For this purpose, out-of-plane formability test method with...

  • Formability Discussion in Dieless Drawing of Stainless Steel Tubes. Yeong-Maw Hwang; Zong-Sian Li; Tsu-Yu Lin // Key Engineering Materials;2014, Vol. 626, p10 

    Stainless steel tubes are widely used in various fields, such as electrode tubes, probe tubes, electronic parts, painless injection needles, and micro-nozzles etc. In this study, a self-developed prototype dieless drawing machine is used to explore the formability of the dieless drawing process...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics