TITLE

Investigation on forming limit properties of dual phase steel

AUTHOR(S)
Pan, Libo; Rolfe, Bernard; Asgari, Alireza; Weiss, Matthias; Zhang, Zhijian
PUB. DATE
May 2013
SOURCE
AIP Conference Proceedings;May2013, Vol. 1532 Issue 1, p850
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The accurate representation of the forming limit properties in the material model is very important for predicting the onset of failure. In this study, the FLCs for two dual phase steels DP780 and DP600 were experimentally obtained. The FLSCs were derived numerically by setting up stretching models in ABAQUS in which experimental FLD data were employed as failure criteria. The results of FLSCs showed in good agreement with that transformed from theoretical calculation. A new type of forming limit diagram based on Polar representation of EPS (Effective Plastic Strain) which proposed by Stoughton and Yoon was conducted to analyse the difference of result caused by FLD and FLSD criteria. The forming processes of a special cup-type part drawing were modelled and simulated by utilizing FLD and FLSD as failure criteria, respectively. According to analysis, the Polar EPS diagram can intuitively describe formability problems in forming processes. To avoid the occurrence of failure, it was found that if strain path for the final stage in Polar EPS diagram can be controlled to locate in some safe zones which can be expressed by function related to some parameters, certain required EPS could be achieved without failure during forming. The results indicated that Polar EPS Diagram seemed to be a good tool to analyse formability in complex strain paths condition and could be used to strengthen formability by designing nonlinear paths.
ACCESSION #
87656112

 

Related Articles

  • Strain-path effects on the formability behavior of Interstitial-Free steel. Ferreira, Jetson Lemos; Amaral Tepedino, José Osvaldo; Wolff, Marco Antonio; Moreira, Luciano Pessanha // Key Engineering Materials;2015, Vol. 651-653, p126 

    In this work, the formability behavior of Interstitial-Free (IF) steel sheet, grade DC07 with 0.65 mm of nominal thickness, was evaluated by means of both linear and bi-linear strainpaths to define the Forming Limit Curve (FLC) at the onset of necking according to ASTM E2218-2 standard. In the...

  • Damage prediction in incremental forming by using Lemaitre damage model. Wu, Shenghua; Reis, Ana; Teixeira, Pedro; da Rocha, A. Barata; Lino, Jorge // AIP Conference Proceedings;Sep2012, Vol. 1479 Issue 1, p1600 

    Incremental forming is an innovative flexible method used for manufacturing of the sheet metal products and brings a great insight for the small-batch-size or customized sheet products. Some experiments show that incremental sheet metal forming can undergo higher deformations than traditional...

  • A comparative study on the formability prediction of steel sheets by anisotropic models based on associated flow rule and non-associated flow rule. Junhe Lian; Deok-Chan Ahn; Dong-Chul Chae; Münstermann, Sebastian; Bleck, Wolfgang // Key Engineering Materials;2015, Vol. 651-653, p150 

    A comparative study on the formability prediction of a ferritic steel sheet by anisotropic models based on associated flow rule and non-associated rule is carried out. The uniaxial tensile tests along seven directions of the sheet from rolling direction to transverse direction with an interval...

  • Forming Limit Diagram Prediction of Tailor-Welded Blank Using Experimental and Numerical Methods. Safdarian Korouyeh, Rasoul; Moslemi Naeini, Hassan; Liaghat, Gholamhosein // Journal of Materials Engineering & Performance;Oct2012, Vol. 21 Issue 10, p2053 

    The forming limit diagram (FLD) is a useful method for characterizing the formability of sheet metals. In this article, different numerical models were used to investigate the FLD of tailor-welded blank (TWB). TWBs were CO laser-welded samples of interstitial-free (IF) steel sheets with...

  • EXPERIMENTAL VERIFICATION OF DIFFERENT THEORETICAL APPROACHES FOR DEFINING FLD. KRAIŠNIK, Milija; VILOTIĆ, Dragiša; ŠIĐANIN, Leposava; PETROVIĆ, Žarko // Annals of the Faculty of Engineering Hunedoara - International J;Feb2014, Vol. 12, p211 

    Workability of materials is the possibility of permanent changes in shape and dimensions of workpieces without cracking or other forms of damage to the structure. This property, which numerically valorized by size of limit effective strain, depends on type of material, the initial structure and...

  • Forming Limits for Three-Dimensional Stress States and Nonlinear Loading Paths. Nurcheshmeh, Morteza; Green, Daniel E. // AIP Conference Proceedings;Dec2013, Vol. 1567 Issue 1, p356 

    The formability of sheet metals is affected by material properties such as the strain hardening ability and strain rate sensitivity as well as process variables such as loading speed, temperature and friction. Much research has been carried out to understand the influence of these parameters on...

  • Forming Limit Strains of Interstitial Free-IF Steel Sheet. Bressan, José Divo; Moreira, Luciano Pessanha; Santos Freitas, Maria Carolina dos // AIP Conference Proceedings;2016, Vol. 1769 Issue 1, p1 

    Present work examines mathematical models to predict the onset of localized necking in sheet metal forming of interstitial free steel, such as biaxial stretching and deep drawing. Forming Limit Curve, FLC, which is an essential material parameter necessary to numerical simulation by FEM, of IF...

  • A practical method to evaluate the forming severity of tubular hydroformed parts. Green, Daniel; Angara, Tirumala; Nurcheshmeh, Morteza; Wormald, Thomas // International Journal of Advanced Manufacturing Technology;Oct2012, Vol. 62 Issue 9-12, p965 

    In view of the prevalence of non-linear strain paths that develop in parts that are formed in multiple stages, such as bent and hydroformed structural components, the conventional forming limit curve (FLC) cannot be used to assess the forming severity of this manufacturing process. A...

  • Predictive performances of FLC using Marciniak-Kuczynski model and Modified Maximum Force Criterion. BANABIC, Dorel; LAZARESCU, Lucian; COMSA, Dan-Sorin // Key Engineering Materials;2015, Vol. 651-653, p96 

    This paper is focused on the performance evaluation of two theoretical models that can be used to predict the Forming Limit Curve (FLC) for an AA6016-T4 aluminium alloy sheet. The FLC is calculated based on the Marciniak-Kuczynski (M-K) model and the Modified Maximum Force Criterion (MMFC) using...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics