TITLE

Consistency condition for isotropic-kinematic hardening of anisotropic yield functions

AUTHOR(S)
Chung, Kwansoo
PUB. DATE
May 2013
SOURCE
AIP Conference Proceedings;May2013, Vol. 1532 Issue 1, p57
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
For the combined type isotropic-kinematic hardening law to account for the Bauschinger, transient and permanent softening behaviors observed in reverse loading, formulations have been initially developed for isotropic yield functions, mainly based on the von Mises criterion, and then later extended for anisotropic yield functions. Among the efforts to introduce anisotropic yield functions to the combined type hardening formulation, however, some inconsistency has been encountered in manipulating the kinematic hardening law, especially for the nonlinear type law, even though their von Mises yield function versions have been consistent. Therefore, theoretical clarification and clearance of such inconsistency were attempted in this work by imposing the following (consistency) condition: the combined type hardening law is expected to behave the same as the full isotropic hardening for monotonously proportional loading, regardless of (anisotropic) yield functions coupled with the combined type hardening law. An example to account for the anisotropic hardening of an anisotropic yield function utilizing the combined type hardening law, but for which the consistency condition was partially released, was also demonstrated.
ACCESSION #
87656085

 

Related Articles

  • Analysis on sheet cyclic plastic deformation using mixed hardening model. Li, Qun; Jin, Miao; Yuxin, Zhu // AIP Conference Proceedings;May2013, Vol. 1532 Issue 1, p982 

    Treating the cyclic deformation problem of sheet flowing through drawbead as the object of the research, using HILL anisotropy yield criterion and mixed hardening model, the cyclic plastic deformation mechanism of sheet was studied, the deformation characteristics of sheet subjected to cyclic...

  • Distribution of Microdefects in Sheets of St1.03-12 Low-Carbon Steel in Tension at Different Rates. Hokhman, O. R.; Volchok, N. A.; Fassmann, D. // Materials Science;Sep2013, Vol. 49 Issue 2, p199 

    We study the influence of the tensile strain rate on the anisotropy of Young’s modulus, the yield strength, and damage coefficient of sheets of St1.03 12 low-carbon steel (0.06 % С, to 0.35 Mn, to 0.40 Si, and ~ 0.025 % S and P). It was established that, with increase in the...

  • Modelling of Strain-Path Transients in Commercially Pure Aluminium. Jisheng Qin; Holmedal, Bjørn; Hopperstad, Oddsture // Materials Science Forum;2017, Vol. 877, p662 

    In the current work, the recently proposed homogeneous anisotropic hardening (HAH) model, featuring a distorted yield surface, is applied to commercially pure aluminium. A dislocation-based hardening rule is incorporated into the HAH model to describe the transient stagnation of the hardening...

  • A Device for the Study of Material Parameters on Bauschinger Effect by Cyclic Bending Tests. Jian LAN; Wei DAI; Hao GAO // Applied Mechanics & Materials;2014, Issue 574, p489 

    A new device to measure the material parameters of Baushinger effect from cyclic bending tests, along with its associated test procedure is presented. This new apparatus is designed to get a large range of stains obtained from part geometry directly. The parameter identification is defined by an...

  • Bauschinger yield in the range 400-1025°C during cyclic deformation of high temperature alloys. Skelton, R. P. // Materials at High Temperatures;Nov2013, Vol. 30 Issue 4, p241 

    Reversed-load (low-cycle-fatigue type) experiments were carried out on 13 different high temperature alloys (ferritic, austenitic and superalloys, single crystal materials, a directionally solidified alloy and two titanium alloys) in the range 400-1025°C. By means of interrupted tests in the...

  • Effect of the kinematic hardening in the simulations of the straightening of long rolled profiles. Bouffioux, Chantal; Boman, Romain; Caillet, Nicolas; Rich, Nicolas; Pontho, Jean-Philippe; Habraken, Anne Marie // Key Engineering Materials;2014, Vol. 611-612, p178 

    Residual stresses and lack of straightness appear during the cooling of sheet piles where the initial temperature field is not homogeneous. To meet the standards, the long hot rolled pieces are straightened using a series of rollers placed alternately above and below the pieces with shifts which...

  • COMPARISON OF THREE METHODS FOR MATERIAL HARDENING PARAMETER IDENTIFICATION UNDER CYCLIC TENSION-COMPRESSION LOADINGS: ROLL LEVELLING CASE STUDY. Silvestre, Elena; de Argandoña, Eneko Sáenz; Galdos, Lander; Mendiguren, Joseba // Key Engineering Materials;2015, Vol. 651-653, p957 

    The roll levelling is a forming process used to remove the residual stresses and imperfections of metal strips by means of plastic deformations. The process is especially important to avoid final geometrical errors when coils are cold formed or when thick plates are cut by laser. In the last...

  • Providing Of High Longevity Of Operating Parts Of Small-Scale Machinery In Agriculture. Chernysh, A. P.; Korchuganova, M. A.; Syrbakov, A. P.; Burunov, A. I. // Applied Mechanics & Materials;2015, Vol. 770, p333 

    The author of the article considers the scientific approaches to increasing the longevity of high-loaded operating parts of small agricultural machines by forming the technological repair units when choosing the optimal methods of hardening the functional surfaces with anti-wear lowcost material.

  • Plastic slip patterns through rate-independent and rate-dependent plasticity. Lancioni, Giovanni; Yalcinkaya, Tuncay // Key Engineering Materials;2014, Vol. 611-612, p1777 

    Plastic deformation induces various types of dislocation microstructures at different length scales, which eventually results in a heterogeneous deformation field in metallic materials. Development of such structures manifests themselves as macroscopic hardening/softening response and plastic...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics