TITLE

Experimental and numerical study of electrically-assisted micro-rolling

AUTHOR(S)
Fan, Rong; Ng, Man-Kwan; Xu, Dongkai; Hu, Ping; Cao, Jian
PUB. DATE
May 2013
SOURCE
AIP Conference Proceedings;May2013, Vol. 1532 Issue 1, p1038
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Electrically-assisted micro-rolling (EAμR) system equipped with surface texturing function was utilized to characterize channel forming behavior of micro-rolling based texturing process. Finite element analyses for both nonelectrically- assisted micro-rolling (NEAμR) and EAμR which accounted for joule heating were performed to verify the experiment results. Furthermore, the influences of joule heating and roll force as well as friction condition on the formed channel profiles were discussed in detail based on the simulation results. It revealed that the formed width and depth of micro-channels were increased with increasing temperature and roll force. Additionally, pile-up at channel opening increased with increasing temperature at lower roll force, however, it decreased with an increase of temperature at higher roll force. It is possible to further improve the formed micro-channel shape by selecting an appropriate combination of roll force and temperature. Moreover, increasing friction helped to achieve larger channel depth, and friction difference between roll-sheet interfaces helped to eliminate the generation of pile-up at micro-channel opening.
ACCESSION #
87656025

 

Related Articles

  • A Study on the Development of Dedicated FEA Tool for Roll Forming of Arbitrary Cross Sections. Cha, Wan-gi; Kim, Hong-lae; Kim, Naksoo // AIP Conference Proceedings;8/22/2011, Vol. 1383 Issue 1, p398 

    In the cold roll forming process, the sheet metal strip is gradually and successively bent into a desired profile. Occurrences of spring back, twist, and bow are major defects in roll formed profiles. We developed a dedicated analysis program based on the elastic-plastic finite element method to...

  • NUMERICAL STUDY REGARDING THE TOOL GEOMETRY IN MULTIPOINT FORMING. PAUNOIU, Viorel; TEODOR, Virgil // Academic Journal of Manufacturing Engineering;Mar2013, Vol. 11 Issue 1, p96 

    In the paper, for a specific profile, the localization of contact points in multipoint forming is analysed. For this, some simulation models using the finite element method were developed. A program for contact points calculation between the part and the tool active elements was designed. For a...

  • SIMULATING RING ROLLING. BUIJK, ARJAAN // Forging;Jul/Aug2011, Vol. 20 Issue 4, p26 

    The article focuses on the first version of special module for ring-rolling simulation introduced by Simufact in 2008. It says that the ring mesher is one of the most important capabilities included in the initial version of the ring-rolling module. It adds that the whole machine control...

  • Influence of tool parameters on tool wear in two-roll cross-wedge rolling. Zhou, Jie; Xiao, Chuan; Yu, Yingyan; Jia, Zhi // International Journal of Advanced Manufacturing Technology;Mar2013, Vol. 65 Issue 5-8, p745 

    A simulation model for two-wedge two-roll cross-wedge rolling was presented by using three-dimensional rigid plastic finite element method. Based on the simulation results, the influence of three tool parameters-the forming angle α, the spreading angle β, and the area reduction Ψ on...

  • Innovations in Rolling Process of Helical Gears. Neugebauer, R.; Hellfritzsch, U.; Lahl, M.; Schiller, S.; Milbrandt, M. // AIP Conference Proceedings;1/17/2011, Vol. 1315 Issue 1, p569 

    By recent studies at Fraunhofer IWU Chemnitz basic information about the material flow in the rolling process of high gearings have been obtained, which provide the necessary data basis for a systematic adjustment of variable geometry and technology parameters. To use these data as efficiently...

  • Modeling and simulation of cold rolling process for double groove ball-section ring. Li, Lanyun; Li, Xiao; Liu, Jing; He, Zhi // International Journal of Advanced Manufacturing Technology;Nov2013, Vol. 69 Issue 5-8, p1717 

    Double groove ball-section ring (DGBR) is an important part of bearing rings. Cold DGBR rolling is an advanced continuous and local plastic forming technique by reducing cross section and increasing the diameter of ring blanks between rotating roll, and can directly obtain the DGBR with good...

  • Simulation modeling of rolling in passes. Chumachenko, E.; Logashina, I.; Aksenov, S. // Metallurgist;Jul2006, Vol. 50 Issue 7/8, p413 

    It is proposed that the three-dimensional problem of rolling in passes be simplified by solving it approximately by the finite-element method. A computer system that has been developed on this basis to model the deformation of metal in passes eliminates having to conduct multiple costly and...

  • Finite Element Analysis of Rolling Process for Pilger Mill. Ning An; Hai Liu // Advanced Materials Research;2014, Issue 881-883, p1420 

    For the simulation of cold rolled 20Cr steel pipe rolling process the DEFORM-3D being used, the simulation results include the equivalent stress, equivalent strain and rolling force distribution in deformation zone. The stress state of the pipe reducer section is analyzed, analysis shows that...

  • Study on Influence of End Concavity of Rolled Piece by Billet Circular Arc Angle with CWR. Hu Bin; Shu Xuedao; Hong Zhe // Applied Mechanics & Materials;2014, Issue 599-601, p478 

    In order to solve the stub bar defects and improve the material utilization, this paper proposes the method of using billet with circular arc shape on the end face to control the end concavity. It establishes the cross wedge rolling finite element model by DEF0RM-3D software, and through the...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics