TITLE

Axial Displacements in Ball Screw Mechanisms with Two and Four Contact-Point

AUTHOR(S)
Penkov, I.; Aleksandrov, D.
PUB. DATE
November 2011
SOURCE
International Review of Mechanical Engineering;Nov2011, Vol. 5 Issue 7, p1213
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The article discusses a calculation procedure for determining the load distribution on the threads of a ball screw under general load condition. The equations for calculating of axial load distribution for two types of loading are presented. The factors influencing the pliability of threads are calculated and their dependence on the pressure angle between balls and elements of transmission is shown. The value of the increment of pressure angle is calculated and the load distribution in a ball screw and a sliding screw is shown. For the ball screw the change of loading for constant and variable pressure angles are considered. Ball screw mechanisms with two and four contact-point rolling elements are considered and equations for calculating of bending and shearing deformations are presented. Radial deformations from contact forces are considered and a simple method for analysis of contact deformations between the balls, screw and nut of the transmission is shown.
ACCESSION #
76127872

 

Related Articles

  • Comparison of rock samples from two different states. Kaur, Kamaljit; Sawant, Vishwas // International Journal of Recent Research Aspects;Sep2016, Vol. 3 Issue 3, p25 

    Experimental work in the labortary found that rock failures are rare when the rock is strong and the stress is low. Some important parameters are influenced by tests in the laboratory on the mechanical behaviour of the intact structure: i) Point load test, ii) Triaxial test. These are the tests...

  • Hysteretic behavior of rectangular tube (box) sections based on Preisach model. Šumarac, Dragoslav; Petrašković, Zoran // Archive of Applied Mechanics;Oct2012, Vol. 82 Issue 10/11, p1663 

    In the present paper, the Preisach model of hysteresis is applied to model cyclic behavior of elasto-plastic material. Rate of loading and viscous effects will not be considered. The problem of axial loading of rectangular cross-section and cyclic bending of rectangular tube (box) will be...

  • Limiting Plastic Load in a Pressure Vessel with a Branch Pipe under Combined Internal Pressure and Bending Moments. Skopinskii, V.; Berkov, N.; Vozhova, N.; Smetankin, A. // Chemical & Petroleum Engineering;Nov2013, Vol. 49 Issue 7/8, p549 

    An applied procedure for elastoplastic analysis, and results of determination of limiting plastic loads for a pressure vessel with a branch pipe under a combined loading are presented. The analysis is performed with the use of the finite-element method, shell theory, plastic-flow theory, and...

  • Cyclic Behavior of Substandard Reinforced Concrete Beam-Column Joints with Plain Bars. Fernandes, Catarina; Melo, José; Varum, Humberto; Costa, Aníbal // ACI Structural Journal;Jan/Feb2013, Vol. 110 Issue 1, p137 

    An experimental investigation aimed at assessing the cyclic behavior of substandard interior beam-column joints built with plain reinforcing bars is described in this paper. Five specimens with plain reinforcing bars and one with deformed bars were tested under reversed cyclic loading. The...

  • SENSIBILITY OF TEETH TO LOADS APPLIED IN DIFFERENT DIRECTIONS. ADLER, PETER // Journal of Dental Research;Aug1947, Vol. 26 Issue 4, p279 

    The article presents a systematic investigation examining the sensibility of teeth to loads applied in different directions. Methods included measurements of groups of individuals to determine strength of forces working on the tooth in axial and lateral directions were perceived as load. Results...

  • Visualization of Multiaxial Stress/Strain State and Evaluation of Failure Life by Developed Analyzing Program under Non-proportional Loading. Shuli LIU; Takamoto ITOH; Noriyuki FUJII // Advanced Materials Research;2014, Issue 891-892, p1391 

    This study presents definitions of principal stress/strain range and mean stress/strain introduced by utilizing Itoh-Sakane criterion for multiaxial loading including non-proportional loading, and shows a method of calculating the non-proportional factor which expresses the severity of...

  • INTEGRATED LOAD OPTIMIZATION OF ELASTIC-PLASTIC AXISYMMETRIC PLATES AT SHAKEDOWN. Venskus, Arturas; Kalanta, Stanislovas; Atkociunas, Juozas; Ulitinas, Tomas // Journal of Civil Engineering & Management;2010, Vol. 16 Issue 2, p203 

    An elastic-plastic axisymmetric steel bending plate subjected to a repeated variable load (RVL) is considered. The solution to the load optimization problem at shakedown is complicated because the stress-strain state of the dissipative systems (e.g. the plate plastic deforming) depends on their...

  • Optimal Domains for Flexural and Axial Loading. Aschheim, Mark; Hernández-Montes, Enrique; Gil-Martín, Luisa María // ACI Structural Journal;Nov/Dec2008, Vol. 105 Issue 6, p720 

    Domains associated with the optimal design of rectangular reinforced concrete sections are established according to the provisions of ACI 318 with respect to P-M coordinates using results obtained with reinforcement sizing diagrams (RSDs). Characteristics of the optimal solutions are identified...

  • Stress Analysis and Determination of Effective k-value for Rigid Pavement. Meshram, Kundan; Goliya, H. S.; Poddar, Akhilesh // International Journal of Engineering Science & Technology;Mar2013, Vol. 5 Issue 3, p468 

    EverFE is a user-friendly 3D finite-element analysis tool for simulating the response of jointed plain concrete pavement (JPCP) systems to axle loads and environmental effects. EverFE is useful for both concrete pavement researchers and designers who must perform either complex nonlinear or...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics