TITLE

Editorial

AUTHOR(S)
Marple, Basil; Agarwal, Arvind; Hyland, Margaret; Lau, Yuk-Chiu; Li, Chang-Jiu; Lima, Rogerio; McDonald, André
PUB. DATE
May 2012
SOURCE
Journal of Thermal Spray Technology;May2012, Vol. 21 Issue 3/4, p361
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
An introduction is presented in which the guest editors discuss various reports within the issue on topics including cold spraying, coating deposition, and coating characterization and performance.
ACCESSION #
74638909

 

Related Articles

  • Tensile Test Specimens with a Circumferential Precrack for Evaluation of Interfacial Toughness of Thermal-Sprayed Coatings. Kishi, Akio; Kuroda, Seiji; Inoue, Tadanobu; Fukushima, Takeshi; Yumoto, Hisami // Journal of Thermal Spray Technology;Jun2008, Vol. 17 Issue 2, p228 

    A new testing procedure to evaluate the interfacial toughness of thermal-sprayed coatings has been developed. The newly designed test specimen is a modification of the pin test with an artificially introduced weak interface, which is expected to open up easily under tensile loading and act as a...

  • Peening Effect of Thermal Spray Coating Process. Jianhong He; Dulin, Bruce; Wolfe, Thomas // Journal of Thermal Spray Technology;Jun2008, Vol. 17 Issue 2, p214 

    The present study investigated the influence of grit blasting, feedstock powder, and thermal spraying technology on performance near the surface on the substrate’s side. The experimental results show that both the grit-blasting process and thermal spraying process harden the substrate,...

  • AE Monitoring and Analysis of HVOF Thermal Spraying Process. Faisal, N. H.; Ahmed, R.; Reuben, R. L.; Allcock, B. // Journal of Thermal Spray Technology;Sep2011, Vol. 20 Issue 5, p1071 

    This work presents an in situ monitoring of HVOF thermal spraying process through an acoustic emission (AE) technique in an industrial coating chamber. Single layer thermal spraying on substrate was carried out through slits. Continuous multilayer thermal spraying onto the sample without slit...

  • Influence of Grit Blasting on the Roughness and the Bond Strength of Detonation Sprayed Coating. Sen, D.; Chavan, Naveen; Rao, D. S.; Sundararajan, G. // Journal of Thermal Spray Technology;Jun2010, Vol. 19 Issue 4, p805 

    The process of roughening the surfaces by grit blasting prior to coating them using thermal spray techniques is very important to obtain consistently high tensile bond strength between the coating and the substrate. The available literature on the influence of grit-blasting parameters in the...

  • Analysis of the Microstructure of Thermal Spray Coatings: A Modeling Approach. Parizi, Hamideh B.; Mostaghimi, Javad; Pershin, Larry; Jazi, Hamid S. // Journal of Thermal Spray Technology;Jun2010, Vol. 19 Issue 4, p736 

    Microstructure of coatings produced by thermal spray coating process depends on many parameters, including particle impact conditions, powder materials, and substrate conditions. Because of the large number of parameters affecting microstructure, developing a computational tool that can predict...

  • Laser-Assisted Cold-Sprayed Corrosion- and Wear-Resistant Coatings: A Review. Olakanmi, E.; Doyoyo, M. // Journal of Thermal Spray Technology;Jun2014, Vol. 23 Issue 5, p765 

    Laser-assisted cold spray (LACS) process will be increasingly employed for depositing coatings because of its unique advantages: solid-state deposition of dense, homogeneous, and pore-free coatings onto a range of substrates; and high build rate at reduced operating costs without the use of...

  • Evaluació n de la corrosió n en solució n de LiBr al 50% en peso de recubrimientos NiCrAlY y NiCrAlCoY. Trujillo-Estrada, A.; Cuevas-Arteaga, C.; Porcayo-Calderón, J. // Superficies y Vacío;2010 Supplement, Vol. 23 Issue S1, p140 

    Corrosion behavior of NiCrAlCoY NiCrAlY coatings deposited by the thermal spraying powder technique on SS 304 substrate exposed in a solution of lithium bromide aqueous solution (50% wt.) at 25°C, 40°C and 70° C, using electrochemical techniques of current and potential noise (EN) and...

  • The Impact of a Partially Molten YSZ Particle. Che-Ming Wu, Tommy; Bussmann, Markus; Mostaghimi, Javad // Journal of Thermal Spray Technology;Dec2009, Vol. 18 Issue 5/6, p957 

    In plasma and high velocity oxy-fuel spraying, a certain portion of the injected powder is often not fully molten upon impact onto a substrate. We present numerical results of the impact of a partially molten yttria-stabilized zirconia particle, a material widely used as a thermal barrier. We...

  • Influence of Bond Coats on the Microstructure and Mechanical Behaviors of HVOF-Deposited TiAlNb Coatings. Zeng, H.; Zhang, L.; Lin, J.; He, X.; Zhang, Y.; Jia, P. // Journal of Thermal Spray Technology;Dec2012, Vol. 21 Issue 6, p1245 

    Hot dip galvanizing has been extensively employed for corrosion protection of steel structures. However, during the process of galvanization, the corrosion in molten zinc brings many problems to galvanization industry. In this study, as a material of corrosion resistance to molten zinc intended...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics