TITLE

Effect of annealing process of iron powder on magnetic properties and losses of motor cores

AUTHOR(S)
Yin, Fuzheng; Yang, Haibo; Tian, Jianjun; Pan, De-An; Wang, Jian; Zhang, Shengen
PUB. DATE
July 2011
SOURCE
Bulletin of Materials Science;2011, Vol. 34 Issue 4, p829
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Iron powder magnetic cores are used as soft magnetic rotors, in micro special motors such as BS brake motors, refrigerator compressor motors and brushless servo motors. Heat treatment of iron powder played an important role in the magnetic properties and loss of the motor cores. After the annealing process, the cracks and the pores on the surface of the powder decreased which in turn decreased the micro-hardness. The Vickers-hardness of the powder decreased from 50-42, while the resistance of the cores increased by 87% after annealing at 400°C for 30 min. The amplitude permeability and magnetic loss of the cores reached the maximum and minimum values, respectively. The magnetic loss of the cores was separated into hysteresis loss and eddy current loss by Stoppels Method which were decreased by the annealing process.
ACCESSION #
66678001

 

Related Articles

  • Amorphous Soft Magnetic Fe80B11Si9 Alloy in Tensile Stress Sensors Application. SALACH, J.; JACKIEWICZ, D.; BIEŃKOWSKI, A.; SZEWCZYK, R.; GRUSZECKA, M. // Acta Physica Polonica, A.;Jul2014, Vol. 126 Issue 1, p102 

    Paper presents the results of investigations of the influence of the tensile stresses on magnetic characteristics of Fe80B11Si9 amorphous alloy in as quenched and annealed state. For the tests, a special methodology of application of uniform tensile stresses to the ring shaped sample was...

  • The Influence of the Different Input Power and Heat Treatment on Structural and Magnetic Properties of Ag73Co27 Magnetic Thin Films. Abdullah, H.; Halim, S. A. // European Journal of Scientific Research;Apr2009, Vol. 29 Issue 3, p388 

    73% Ag ~ 27% Co film were deposited onto (100) Si substrate via radio frequency (RF) magnetron sputtering. The influence of RF input power on magnetic and structural properties of films was investigated. The XRD spectra show that a set of (111), (200), (220) and (311) peaks were observed. X-ray...

  • STUDY OF SECONDARY RECRYSTALLIZATION IN GRAIN-ORIENTED STEEL TREATED UNDER DYNAMICAL HEAT TREATMENT CONDITIONS. Stoyka, V.; Kovac, F.; Julius, B. // Metalurgija;2009, Vol. 48 Issue 2, p99 

    The present study was made to investigate secondary recrystallization in grain-oriented steels annealed at short time temperature exposures with application of dynamical heating. The investigated GO steels for experiments were taken from one industrial line after final cold rolling reduction and...

  • Low-temperature ordering of FePt thin films by a thin AuCu underlayer. Yun Zhu; Cai, J. W. // Applied Physics Letters;7/18/2005, Vol. 87 Issue 3, p032504 

    We have studied the magnetic and structural properties of AuCu(0–50 nm)/FePt(2–50 nm) films after annealing at various temperatures. The results indicate that, by introducing a thin equiatomic AuCu underlayer, the ordering temperature of FePt films with thickness even down to 5 nm...

  • Magnetic properties of Co–Al melt-spun ribbons. Saito, Tetsuji // Journal of Applied Physics;4/15/2006, Vol. 99 Issue 8, p08E905 

    Co–Al alloy ribbons were produced by melt spinning followed by heat treatment. Although the Co–Al melt-spun ribbons had low coercivities, annealing of the ribbons resulted in an increase in the coercivity. The optimally annealed Co75Al25 melt-spun ribbon exhibited a high coercivity...

  • Magnetic susceptibility and thermal stability of particle size of nanocrystalline tungsten carbide WC. Kurlov, A.; Nazarova, S.; Gusev, A. // Physics of the Solid State;Sep2007, Vol. 49 Issue 9, p1780 

    The magnetic susceptibility χ of coarse-grained and nanocrystalline tungsten carbides was studied in the temperature range 300–1250 K. The temperature dependence of the susceptibility χ( T) of coarse-grained carbide WC is typical of weak Pauli paramagnets and has no specific...

  • Effect of Cooling Rate in Heat Treatment on the Magnetic Properties of Amorphous Cobalt-Based Alloys of the AMAG Type. Chernov, V. S.; Ivanov, O. G. // Metal Science & Heat Treatment;May/Jun2004, Vol. 46 Issue 5/6, p206 

    Results of a study of the effect of a wide range of cooling rates in thermal and thermomagnetic treatment on the magnetic properties (permeability, coercive force, and coefficient of squareness) of amorphous strips from magnetically soft cobalt-based alloy AMAG 176 of the Co – Fe –...

  • Annealing: Making metals workable. Petry // Metal Center News;Sep99, Vol. 39 Issue 10, p24 

    Offers an overview of annealing. Features of bell-type hydrogen annealing equipment; Real world applications of the annealing technology; Reduction of brittleness of metals through annealing; Distortion of steel's grain structure beyond its elastic limit; Increase of ductility; Relief of...

  • Structural and electrical characteristics of thin erbium oxide gate dielectrics. Tung-Ming Pan; Chun-Lin Chen; Wen Wei Yeh; Sung-Ju Hou // Applied Physics Letters;11/27/2006, Vol. 89 Issue 22, p222912 

    A high-k erbium oxide thin film was grown on silicon substrate by reactive rf sputtering. It is found that the capacitance value of Er2O3 gate dielectric with TaN metal gate annealed at 700 °C is higher compared to other annealing temperature and exhibits a lower hysteresis voltage as well as...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics