TITLE

Note: Autonomous pulsed power generator based on transverse shock wave depolarization of ferroelectric ceramics

AUTHOR(S)
Shkuratov, Sergey I.; Baird, Jason; Talantsev, Evgueni F.
PUB. DATE
December 2010
SOURCE
Review of Scientific Instruments;Dec2010, Vol. 81 Issue 12, p126102
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Autonomous pulsed generators utilizing transverse shock wave depolarization (shock front propagates across the polarization vector P0) of Pb(Zr0.52Ti0.48)O3 poled piezoelectric ceramics were designed, constructed, and experimentally tested. It was demonstrated that generators having total volume of 50 cm3 were capable of producing the output voltage pulses with amplitude up to 43 kV with pulse duration 4 μs. A comparison of high-voltage operation of transverse and longitudinal shock wave ferroelectric generators is given.
ACCESSION #
65091199

 

Related Articles

  • Note: Miniature 120-kV autonomous generator based on transverse shock-wave depolarization of Pb(Zr0.52Ti0.48)O3 ferroelectrics. Shkuratov, Sergey I.; Baird, Jason; Talantsev, Evgueni F. // Review of Scientific Instruments;Aug2011, Vol. 82 Issue 8, p086107 

    The design of autonomous ultrahigh-voltage generators with no moving metallic parts based on transverse explosive shock wave depolarization of Pb(Zr0.52Ti0.48)O3 (PZT 52/48) poled ferroelectrics was explored and studied. It follows from experimental results that the output voltage produced by...

  • 1218. The calibration of sinusoidal excitation force of piezoelectric ceramic exciter. Hui Li; Wei Sun; Ying Liu; Qingkai Han // Journal of Vibroengineering;Mar2014, Vol. 16 Issue 2, p1080 

    Piezoelectric ceramic exciter (PCE) have been used to experimentally study on the inherent and damping characteristics of thin-walled structures. However, due to its unknown excitation force level, it can not be applied on more practical cases in which accurate test of dynamic response is...

  • Compact high-voltage generator of primary power based on shock wave depolarization of lead zirconate titanate piezoelectric ceramics. Shkuratov, Sergey I.; Talantsev, Evgueni F.; Menon, Latika; Temkin, Henryk; Baird, Jason; Altgilbers, Larry L. // Review of Scientific Instruments;Aug2004, Vol. 75 Issue 8, p2766 

    The design and performance of a compact explosive-driven high-voltage primary power generator is presented. The generator utilizes a fundamental physical effect—depolarization of ferroelectric materials under longitudinal shock wave impact, when the shock wave is initiated along the...

  • Enhanced performance of wearable piezoelectric nanogenerator fabricated by two-step hydrothermal process. Yu Qiu; Jixue Lei; Dechao Yang; Bing Yin; Heqiu Zhang; Jiming Bian; Jiuyu Ji; Yanhong Liu; Yu Zhao; Yingmin Luo; Lizhong Hu // Applied Physics Letters;3/17/2014, Vol. 104 Issue 11, p1 

    A simple two-step hydrothermal process was proposed for enhancing the performance of the nanogenerator on flexible and wearable terylene-fabric substrate. With this method, a significant enhancement in output voltage of the nanogenerator from ~10mV to 7V was achieved, comparing with the one by...

  • Development of a piezoelectric micropump with novel separable design. Wen-Fu Luo; Hsiao-Kang Ma // Applied Mechanics & Materials;2014, Issue 667-679, p1426 

    In this study, partially disposable piezoelectric micropumps with separable design have been developed and discussed. The actuator, a rectangular piezo-plate, can be separated and be used repeatedly while the pump chamber is single-use to prevent infection. Thus, a low cost and waste solution...

  • Design of Piezoelectric PZT Cantilever for Actuator Application. Joshi, Abhay B.; Bodas, Dhananjay; Gangal, S. A. // Sensors & Transducers (1726-5479);Dec2010, Vol. 123 Issue 12, p16 

    Piezoelectric MEMS cantilever is used as a basic element in sensing and actuation. This paper proposes a structural design of MEMS cantilever for actuator application based on bulk MEMS micromachining technique. The structure consists of a silicon dioxide cantilever with an attached...

  • Toko Develops Piezoelectric Element for Ultrasonic Motors.  // American Ceramic Society Bulletin;Nov2007, Vol. 86 Issue 11, p6 

    The article reports on the development of a piezoelectric element by Toko Inc. to drive ultrasonic motors. The company's element only requires one pair of electrodes that will make the element simpler and less expensive to produce. Moreover, the piezoelectric element uses an alumina chip to...

  • Temperature dependence of the complex effective piezoelectric coefficient of ferroelectric 0-3 composites. Wong, C. K.; Poon, Y. M.; Shin, F. G. // Journal of Applied Physics;9/15/2002, Vol. 92 Issue 6, p3287 

    Temperature dependence of the complex effective piezoelectric coefficient d[sup *, sub 3l] for a ferroelectric 0-3 composite of small ceramic volume fraction has been studied. Theoretical predictions are based on our previously derived explicit expression of d[sub 31] for a dilute dispersion of...

  • Modeling of poling behavior of ferroelectric 1-3 composites. Hauke, T.; Steinhausen, R.; Seifert, W.; Beige, H.; Kamlah, M. // Journal of Applied Physics;5/1/2001, Vol. 89 Issue 9, p5040 

    Piezoelectric 1-3 composites are typically prepared from a polymer matrix and an unpoled Pb(Zr[sub x]Ti[sub 1-x])O[sub 3] (PZT) based ceramic. During the subsequent poling process the PZT cannot strain freely due to the clamping by the surrounding polymer, which after poling results in the...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics