TITLE

Numerical simulation of the [sup 48]Ca[sup 5+] ions transport along the U-400 cyclotron’s injection line

AUTHOR(S)
Aleksandrov, V. S.; Gulbekian, G. G.; Kazarinov, N. Yu.; Shevtsov, V. F.; Tikhomirov, A. V.
PUB. DATE
December 2001
SOURCE
AIP Conference Proceedings;2001, Vol. 600 Issue 1, p390
SOURCE TYPE
Conference Proceeding
DOC. TYPE
Article
ABSTRACT
The numerical simulation of the [sup 48]Ca[sup 5+] ions beam transport along the U-400 cyclotron's injection line has been carried out. Space charge effects of multi-charged ions spectrum extracted from ECR-source and the longitudinal beam compression influence of two bunchers (sine and line types) on the transverse beam dynamics have been taken into consideration in the process of the beam transport optimization. The simulation results are compared for two injection line schemes: of presently utilized line and its reconstructed variant. The injection line reconstruction does not require any new ion-optic elements. It assumes the exception of the 102° horizontal bending magnet from the present injection line. Eventually this reconstruction will give meaningful transport line shortening. According to produced simulation the expected transmission efficiency from the ECR-source to the cyclotron's spiral inflector entrance along the reconstructed injection line will be essentially increased, as well as appreciably more [sup 48]Ca[sup 5+] beam intensity level will be provided.
ACCESSION #
6220762

 

Related Articles

  • Measurement of axial injection displacement with trim coil current unbalance. Kireeff Covo, Michel // Review of Scientific Instruments;2014, Vol. 85 Issue 8, p1 

    The Dee probe used for measuring internal radial beam intensity shows large losses inside the radius of 20 cm of the 88 in. cyclotron. The current of the top and bottom innermost trim coil 1 is unbalanced to study effects of the axial injection displacement. A beam profile monitor images the ion...

  • Performance and operation of a beam chopping system for a cyclotron with multiturn extraction. Yokota, W.; Fukuda, M.; Okumura, S.; Arakawa, K.; Nakamura, Y.; Nara, T.; Agematsu, T. // Review of Scientific Instruments;Apr97, Vol. 68 Issue 4, p1714 

    Describes the performance and operation of a beam chopping system for a cyclotron with multiturn extraction. Beam chopping system at the Japan Atomic Energy Research Institute; Review of the chopping process; Performance of each chopper; Single-pulse beams and multiturn extraction.

  • A time pickup system for monitoring cyclotron beam bursts. Okumura, S.; Fukuda, M.; Ishibori, I.; Arakawa, K. // Review of Scientific Instruments;Jan2002, Vol. 73 Issue 1, p51 

    We have developed a time pickup system for monitoring the beam bursts from a cyclotron. The time pickup can measure the phase and the width of the beam bursts by detecting secondary electrons emitted from a foil or a wire target inserted into the beam with time resolutions around 200 ps full...

  • Modification of a double drift beam bunching system to get the efficiency of a six harmonic buncher. Pandit, V. S.; Sarma, P. R.; Bhandari, R. K. // AIP Conference Proceedings;2001, Vol. 600 Issue 1, p452 

    We have proposed a double drift bunching scheme where one can obtain a bunching effect equal to that of a sixharmonic buncher by using only two harmonics mixed in optimum proportions. In this case one has to apply voltages with frequencies ω and 2 ω (instead of only ω) on the first...

  • NORTICA—a new code for cyclotron analysis. Gorelov, D.; Johnson, D.; Marti, F. // AIP Conference Proceedings;2001, Vol. 600 Issue 1, p414 

    The new package NORTICA (Numerical ORbit Tracking In Cyclotrons with Analysis) of computer codes for beam dynamics simulations is under development at NSCL. The package was started as a replacement for the code MONSTER [1] developed in the laboratory in the past. The new codes are capable of...

  • Effects of vertical misalignment of superconducting coils in cyclotrons. Kim, Jong-Won // AIP Conference Proceedings;2001, Vol. 600 Issue 1, p405 

    A vertical beam loss on the extraction elements of the KS00 cyclotron has been observed during commissioning of the Coupled Cyclotron Project. The cause was found to be the misalignment of coils, and the coil shift vertically about 1 mm made a correction. The vertical displacement of a 9.5 MeV/u...

  • Design of the injection channel magnets for the K1200 cyclotron. Wu, X. Y.; Lawton, D.; Marti, F.; Zeller, A. F. // AIP Conference Proceedings;2001, Vol. 600 Issue 1, p342 

    The beam from the K500 cyclotron is injected radially into the median plane of the K1200 cyclotron where it is stripped inside a dee. Along the injection path, the injected beam traverses large magnetic gradients under the K1200 superconducting coil and on the edge of the hill. To match the...

  • New Rebunchers for HIRFL-CSR. Tang, J. Y.; Li, Z. H.; Zheng, Q. W.; Zhou, X. H.; Yuan, Y. J.; Li, H. H.; Huang, T. Z.; Nie, Y. Z.; Zhang, B. // AIP Conference Proceedings;2001, Vol. 600 Issue 1, p309 

    Three almost-identical rebunchers have been designed for HIRFL-CSR. The first one B 1 is going to be taken the off-line test and will be installed in place soon. The rebunchers B1 and B2 are in the BL1 beam line from the injector cyclotron SFC to the main cyclotron SSC, together for the...

  • Status and special features of the Atomki ECR ion source. Biri, S.; Rácz, R.; Pálinkás, J. // Review of Scientific Instruments;Feb2012, Vol. 83 Issue 2, p02A341 

    The ECR ion source has been operating in ATOMKI (Debrecen) since 1996. During the past 15 years lots of minor and numerous major technical modifications have been carried out on the ECRIS. Many of these changes aimed the increasing of beams charge, intensity, and the widening of the ion choice....

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics