Esistenza del modo O in piastre tridimensionali con fori circolari ed ellittici soggette a modo II

Berto, Filippo; Marangon, Christian
January 2011
Frattura e Integrita Strutturale;2011, Issue 15, p14
Academic Journal
No abstract available.


Related Articles

  • Failure Analysis With a New Tool Geometry, X-Die, in Areas With High Tension/Compression Strains. Andersson, Alf; Thilderkvist, Per // AIP Conference Proceedings;2007, Vol. 908 Issue 1, p1445 

    Sheet-metal forming involves a complex strain distribution over the part. The strains consist of tension, compression, and a mix of both. A geometry has been developed, the X-Die, in order to gain insight into the strain behavior of different materials. The X-Die enables strain paths far into...

  • Bending analysis of thin functionally graded plates using generalized differential quadrature method. Fereidoon, A.; Asghardokht seyedmahalle, M.; Mohyeddin, A. // Archive of Applied Mechanics;Nov2011, Vol. 81 Issue 11, p1523 

    In this paper, the differential quadrature (DQ) method is presented for easy and effective analysis of isotropic functionally graded (FG) and functionally graded coated (FGC) thin plates with constant Poisson's ratio and varying Young's modulus in the thickness direction. The bending of FG and...

  • Analytical Solutions for Buckling of Functionally Graded Circular Plates under Uniform Radial Compression using Bessel Function. Heydari, A. // International Journal of Advanced Design & Manufacturing Technol;Dec2013, Vol. 6 Issue 4, p41 

    The current study presents a new analytical method for buckling analysis of circular plates with constant thickness and Poisson's ratio, made of functionally graded material subjected to radial loading. Governing equations are based on energy method for thin plates. The boundary conditions of...

  • Springback Analysis in Sheet Metal Forming Using Modified Ludwik Stress-Strain Relation. Kumar Patel, Sanjay; Krishna Lal, Radha; Dwivedi, J. P.; Singh, V. P. // ISRN Mechanical Engineering;2013, p1 

    This paper deals with the springback analysis in sheet metal forming using modified Ludwik stress-strain relation. Using the deformation theory of plasticity, formulation of the problem and spring back ratio is derived using modified Ludwik stress strain relationship with Tresca and von Mises...

  • Auxetic Plates on Auxetic Foundation. Teik-Cheng Lim // Advanced Materials Research;2014, Vol. 974, p398 

    Auxetic solids are materials that exhibit negative Poisson's ratio. This paper evaluates the maximum stresses in point-loaded (a) auxetic plates on conventional elastic foundation, (b) conventional plates on auxetic elastic foundation, and (c) auxetic plates on auxetic elastic foundation...

  • Analytical and numerical modeling of pullout capacity and interaction between hexagonal wire mesh and silty sand backfill under an in-soil pullout test. Bergado, Dennes T; Teerawattanasuk, Chairat; Kongkitkul, Warat // Canadian Geotechnical Journal;Oct2003, Vol. 40 Issue 5, p886 

    During the pullout test, the pullout clamping system was modified and installed inside the pullout box with confinement from the fill material, hereinafter called the in-soil pullout test, which significantly reduced the necking phenomenon and the displacements mobilized during the pullout test....

  • Physically and Geometrically Nonlinear Static Problems for Thin-Walled Multiply Connected Shells. Guz, A. N.; Storozhuk, E. A.; Chernyshenko, I. S. // International Applied Mechanics;Jun2003, Vol. 39 Issue 6, p679 

    Physically and geometrically nonlinear two-dimensional problems are formulated for multiply connected thin shells (weakened by several curvilinear holes). A technique and algorithm are proposed for their solution with allowance for elastoplastic strains and finite deflections of shells under...

  • Analysis of the stressed state of flexible annular plates whose thickness varies in two directions. Narol's'kyi, лю. // Journal of Mathematical Sciences;Oct2012, Vol. 186 Issue 1, p93 

    We consider the problem of the change in the stress-strain state of an annular plate of varying rigidity under the action of a nonstationary magnetic field and perform an analysis of electromagnetic effects in the nonlinear statement. Graphs of numerical computations that illustrate the...

  • Testing of Pre-stressing Masonry Wall with Using Different Thickness of Anchor Plates. Stara, Marie // Advanced Materials Research;11/14/2014, Vol. 1082, p211 

    Contribution deals with experimental measurements of deformations in the place exposed to local load caused by additional pre-stressing. The measurements are made at the masonry brick corner built in the laboratory equipment. The laboratory equipment was designed at Faculty of Civil Engineering...


Read the Article


Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics