TITLE

Consideration of stress gauges in the modelling of plate impacts

AUTHOR(S)
Church, P.; Townsley, R.; Millett, J.
PUB. DATE
April 2000
SOURCE
AIP Conference Proceedings;2000, Vol. 505 Issue 1, p1083
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The modelling of a plate impact experiment has been carried out using the Lagrangian hydrocode DYNA. In the experimental setup the shock wave is analysed using a gauge sandwiched between the two stationary plates. The investigation of the shock wave in the simulation would normally entail examining data recorded by a single element approximating the gauge. An attempt was made to crudely model the actual gauge used. Differing levels of complexity in the representation of the gauge were simulated, and their effect on the shock wave examined. The simulation used a recently developed path dependent model for copper which has been shown to perform well in a variety of scenarios. This paper discusses various issues concerning the comparison with gauge results in plate impact experiments.
ACCESSION #
5985629

 

Related Articles

  • The Behaviour of Dry Sand under Shock-Loading. Chapman, D. J.; Tsembelis, K.; Proud, W. G. // AIP Conference Proceedings;2006, Vol. 845 Issue 1, p1445 

    Plate impact experiments have been performed in forward and reverse impact configurations on dry, quartz sand to obtain Hugoniot data. In the forward configuration, manganin gauges were placed both in surrounding anvils and in the sand. Gauges placed directly in or near the sand gave anomalously...

  • Lateral stress measurement in shock-loaded targets with transverse piezoresistance gauges. Rosenberg, Z.; Partom, Y. // Journal of Applied Physics;10/15/1985, Vol. 58 Issue 8, p3072 

    Presents an analytical model for the calibration of lateral piezoresistance stress gauges in shock-wave experiments. Importance of the determination of the lateral stress in the shocked specimen; Description on an analytical calibration of the transverse gauge; Approach to the calibration of...

  • Initiation of EDC-37 measured with embedded electromagnetic particle velocity gauges. Gustavsen, R. L.; Sheffield, S. A.; Alcon, R. R.; Hill, L. G.; Winter, R. E.; Salisbury, D. A.; Taylor, P. // AIP Conference Proceedings;2000, Vol. 505 Issue 1, p879 

    Planar shock wave initiation of the explosive EDC-37 was studied using multiple embedded magnetic particle velocity gauges. EDC-37 consists of (by weight) 91% HMX, 1% nitrocellulose, and 8% K10, a liquid eutectic mixture of di- nitro-ethyl-benzene and tri-nitro-ethyl-benzene. Its nominal density...

  • Steady-wave characteristics in shock-loaded steel specimens. Rosenberg, Z.; Bless, S. J. // Journal of Applied Physics;2/15/1986, Vol. 59 Issue 4, p1384 

    Presents information on a study which explored the steady-wave features of the plastic shock wave in low carbon steel with Manganin stress gauges. Features of the waves; Response time of the gauge; Conclusions.

  • Failure Waves in Shock-Compressed Glasses. Kanel, G. I. // AIP Conference Proceedings;2006, Vol. 845 Issue 1, p870 

    The failure wave is a network of cracks that are nucleated on the surface and propagate into the elastically stressed body. It is a mode of catastrophic fracture in an elastically stressed media whose relevance is not limited to impact events. In the paper, main properties of the failure waves...

  • Stabilization of Wave Formation on a Contact Boundary of Metal Layers at an Oblique Impact during Kelvin - Helmholtz Instability Development. Drennov, O. B.; Mikhailov, A. L. // AIP Conference Proceedings;2006, Vol. 845 Issue 1, p1375 

    The elimination effect of disturbances and mutual mixing on a contact boundaries of metal layers at oblique impact during Kelvin - Helmholtz instability development was established and investigated. Thin layers of metal coatings (Δ∼30 μm) reduce amplitude of disturbance realization...

  • Performance of Simplified Damage Assessment Tools for Reinforced Concrete Panels under Blast Loading. Syed, Zubair Imam; Liew, Mohd Shahir; Mendis, Priyan // Key Engineering Materials;2014, Vol. 594/595, p492 

    Pressure-impulse (P-I) and charge weight-distance (CW-D) diagrams are widely used as quick damage assessment tools for reinforced concrete (RC) elements exposed to blast loading. Depending on the loading and element properties, the blast loading can induce different patterns of response and...

  • SHOCKWAVES IN CONVERGING GEOMETRIES. Brown, J. L.; Ravichandran, G. // AIP Conference Proceedings;12/28/2009, Vol. 1195 Issue 1, p747 

    Plate impact experiments are a powerful tool in equation of state (EOS) development, but are inherently limited by the range of impact velocities accessible to the gun. In an effort to dramatically increase the range of pressures which can be studied with available impact velocities, a new...

  • Response measurements on an echinodome subjected to explosive loading. El-Deeb; Royles // Shock & Vibration;1999, Vol. 6 Issue 1, p45 

    Free field explosion experiments were carried out to determine the general characteristics of the pressure pulse generated by a detonator underwater. An echinodome – an axisymmetric shell structure of optimum form – was subjected to a shock wave from the same type of detonator, the...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics