TITLE

Dynamic yield strength and spall strength determination for AerMet® 100 steels

AUTHOR(S)
Reinhart, W. D.; Chhabildas, L. C.; Wilson, L. T.
PUB. DATE
April 2000
SOURCE
AIP Conference Proceedings;2000, Vol. 505 Issue 1, p471
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Well-controlled impact studies have been conducted on "as-received" and heat-treated AerMet[SUP®] 100 steel alloy samples to determine their dynamic material properties. In particular, gas gun and time-resolved laser interferometry have been used to measure the fine structure in the particle velocity profiles resulting from symmetric plate impact. Impact velocities ranged from 0.40 km/s to 0.90 km/s. These experiments have allowed us to estimate the dynamic yield and spall strengths of the "as-received" and heat-treated AerMet[SUP®] 100 steel.
ACCESSION #
5985483

 

Related Articles

  • FRACTURE MECHANICAL MEASUREMENTS WITH COMMERCIAL STAINLESS STEELS AT 4 K AND WITH CP-TITANIUM AT 173 K. Nyilas, A.; Mitterbacher, H. // AIP Conference Proceedings;4/8/2010, Vol. 1219 Issue 1, p33 

    Using the JETT (J-Evaluation on Tensile Test) technique, measurements have been performed with commercial stainless steels in forged and cast condition for the reason of an assessment for low temperature service down to 4 K. These steels frequently used for industrial applications are designated...

  • Evaluation of the test temperature effect on failure mechanisms and notched impact strength characteristics of ultra-hard low alloy steels. Binar, T.; Kadlec, J.; Rejzek, M.; Vlkovsky, M.; Hruby, V. // Strength of Materials;Aug2011, Vol. 43 Issue 5, p537 

    We evaluate, by means of fractographic analysis of fracture surfaces, changes in failure mechanism depending on the test temperature of ultra-hard low alloy steels ARMOX 500 T and ARMOX 600 T. Experimental investigation temperatures range was from −80 to 100°C, where the occurrence of a...

  • Plastic Alloy Steel: Crack Growth Behavior Controlled by Anisotropy of Properties and Service Time*. Veselukha, V.; Bogdanovich, A.; Kozik, A.; Vorob'ev, V. // Strength of Materials;Sep2014, Vol. 46 Issue 5, p683 

    Crack resistance test results for plastic steel specimens cut from the pipe of the linear section of an oil pipeline are discussed. For studying anisotropy of properties, the crack in the specimen was oriented in the axial and circumferential pipe directions. Cyclic crack resistance values for...

  • Fracture Mechanics of Crack Growth During Sonic-IR Inspection. Chen, J. C.; Riddell, W. T.; Lick, Kyle; Chang-Hwa Wong // AIP Conference Proceedings;2007, Vol. 894 Issue 1, p507 

    In past studies, we showed that cracks synthesized under carefully controlled conditions will propagate when subjected to sonic IR testing. The extent or severity of the propagation observed depended on several parameters including the stress intensity factor (which corresponds to crack growth...

  • EVALUATION OF FIVE FRACTURE MODELS IN TAYLOR IMPACT FRACTURE. Wei Zhang; Xinke Xiao; Gang Wei; Zitao Guo // AIP Conference Proceedings;2012, Vol. 1426 Issue 1, p1125 

    Taylor impact test presented in a previous study on a commercial high strength and super hard aluminum alloy 7A04-T6 are numerically evaluated using the finite element code ABAQUS/Explicit. In the present study, the influence of fracture criterion in numerical simulations of the deformation and...

  • Damages Caused by Projectile Impact. Zaid, Adnan I. O. // Key Engineering Materials;2016, Vol. 689, p29 

    Impact conditions involve velocities below the sonic speed, which is normally of the order few hundreds up to few thousands m/s. The implications of impact depend on projectile and target materials, impact velocity, incident angle and the mass and shape of the projectile impacting head. The...

  • Further aspects on J-evaluation demonstrated with EDM notched round bars and double-edged plates between 300 and 7 K. Nyilas, A.; Nishimura, A.; Obst, B. // AIP Conference Proceedings;2002, Vol. 614 Issue 1, p131 

    Based on recent experiences with respect to JETT (J-Evaluation on Tensile Test) several materials were measured to investigate the potential of this novel technique with the aim to determine the fracture toughness of materials. The investigated materials covered a wide field of toughness levels...

  • Effect of Oriented Elastic and Strength Characteristics on the Impact Fracture of Anisotropic Materials. Radchenko, Andrew V.; Kobenko, Sergey V.; Krivosheina, Marina N. // AIP Conference Proceedings;2002, Vol. 620 Issue 1, p543 

    In paper, the influence of orientation of strength properties on destruction of materials under impact is investigated numerically. The numerical modeling was carried out in three-dimensional statement by a method of finite elements in frameworks of the continual approach of the mechanics of...

  • Effect of impact modification on slow crack growth in poly(vinyl chloride). Bernal-Lara, T. E.; Hu, Y.; Summers, J.; Hiltner, A.; Baer, E. // Journal of Materials Science;May2004, Vol. 39 Issue 9, p2979 

    The effect of impact modification on slow crack growth in a poly(vinyl chloride) (PVC) compound was examined in order to test a methodology for predicting long-term creep fracture from short-term tension-tension fatigue tests. In all cases the crack propagated in a stepwise manner through a...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics