TITLE

Keeping your motors running

AUTHOR(S)
Raleigh, Patrick
PUB. DATE
January 2011
SOURCE
Process Engineering;Jan/Feb2011, Vol. 92 Issue 1, p37
SOURCE TYPE
Trade Publication
DOC. TYPE
Article
ABSTRACT
The author discusses the strategies on motor maintenance for manufacturing process. The author suggests to focus on the problems cited on the engine by checking the bearings through condition monitoring. The author highlights the condition monitoring methods including electrical testing, thermal imaging, and oil analysis. The rewinding of motors is also mentioned.
ACCESSION #
57936624

 

Related Articles

  • CHAPTER FIVE -- ENGINE LOWER END.  // Yamaha V-Max, 1985-2007;2013, p130 

    The article offers information on components of engines which can be removed and installed during servicing procedures. It informs that components such as crankshaft is located in crankcase and supported by four pairs of bearings. It states that before removal of crankshaft engines are cleaned...

  • WAVELET-BASED ALGORITHM FOR DETECTION OF BEARING FAULTS IN A GAS TURBINE ENGINE. Enchev, Sergiy; Tovkach, Sergiy // Proceedings of National Aviation University;2014, Vol. 2 Issue 59, p88 

    Presented is a gas turbine engine bearing diagnostic system that integrates information from various advanced vibration analysis techniques to achieve robust bearing health state awareness. This paper presents a computational algorithm for identifying power frequency variations and integer...

  • CHAPTER THREE -- LUBRICATION, MAINTENANCE AND TUNE-UP -- TIRES AND WHEELS.  // Yamaha V-Max, 1985-2007;2013, p90 

    The article offers step-by-step instructions for the inspection of tire, rim and wheel bearing in Yamaha motor bike engines.

  • Using vibration analysis to detect early failure of bearings. Lacey, S. J. // Insight: Non-Destructive Testing & Condition Monitoring;Aug2007, Vol. 49 Issue 8, p444 

    Vibration produced by rolling bearings can be complex and can result from geometrical imperfections during the manufacturing process, defects on the rolling surfaces or geometrical errors in associated components. Noise and vibration is becoming more critical in all types of equipment since it...

  • Race Tips for Spec Motors. Suangka, Charlie // RC Driver;Mar2012, Issue 99, p104 

    The article presents tips to improve the performance of spec motors. Checking and cleaning of the motors are suggested to prevent gritty bearings. Strong rotors are described to have a solid feel when the magnet clicks during rotation of the shaft. In addition, plugging the sensor harness...

  • Chapter Five -- Engine Lower End -- Crankcase Seals and Bearings.  // Yamaha Rhino 700, 2008-2012;2012, p139 

    The article presents a section of the Chapter Five, Engine Lower End, of the shop manual "Yamaha Rhino 700, 2008-12," in which step-by-step instructions on how to remove and install crankcase seals and bearings are presented.

  • Steel Bearing Production Cycle.  // Industrial Heating;May2013, Vol. 81 Issue 5, following p84 

    The article discusses the production cycle of steel bearing, from material selection to post-process verification.

  • Tune-up Time. Sargeant, Frank // Outdoor Life;Dec/Jan2003, Vol. 210 Issue 1, p123 

    Presents maintenance tips for outboard motors. Application of fuel conditioner or preservative; Steps in removing water in the cooling system; Suggestions on oil change.

  • Chapter Three -- Troubleshooting -- Engine And Drive Identification. Rolling, Mark; Killingsworth, Jeff // MerCruiser Stern Drive Shop Manual Alpha, Bravo One, Bravo Two &;2015, p29 

    The article discusses how to identify the engine and drive model before ordering replacement parts or performing testing or repairs, and mentions topics that include primary serial number tag, engine serial number, drive unit serial number, and transom assembly serial number.

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics