TITLE

CORROSION STUDY ON COPPER PROCESSED BY ROLLING WITH DIFFERENT DEFORMATION DEGREES AND RECRYSTALLIZED AT DIFFERENT TEMPERATURES

PUB. DATE
January 2011
SOURCE
Metalurgia;ene2011, Vol. 63 Issue 1, p48
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
No abstract available.
ACCESSION #
57631869

 

Related Articles

  • Structural and kinetic features of dynamic recrystallization of alloyed austenite upon multipass hot deformation. Kunitskaya, I.; Spektor, Ya.; Olshanetskii, V. // Metal Science & Heat Treatment;Jan2012, Vol. 53 Issue 9/10, p498 

    The kinetics is studied and the mechanism of dynamic recrystallization is amended for the alloyed Cr - Ni - Mo - Ti austenite of special steels upon multipass hot deformation by rolling and twisting in the range of 900 - 1300°C. The structural features of nucleation of fine and ultrafine...

  • Microstructure and Superplasticity of an Al-Mg-Sc-Zr alloy Processed by ECAP and Subsequent Cold Rolling. Avtokratova, Elena; Sitdikov, Oleg; Mukhametdinova, Oksana; Markushev, Michael; Murty, S. V. S. Narayana; Prasad, M. J. N. V.; Kashyap, Bhagwati P. // Materials Science Forum;2015, Vol. 830-831, p345 

    The feasibility has been demonstrated for achieving high-strain-rate superplasticity with elongations beyond 2000% in Al-Mg-Sc-Zr alloy with the partially recrystallized structure, produced by warm equal-channel angular pressing to strain of e~3 only. Subsequent alloy ambient temperature rolling...

  • Behavior of flow stress of Al-Mn alloy during hot compression. Xiao Zhang; Zheng Ren; Xiurong Zhu; Jing Ren; Fukui Lian; Liqun Hou // Advanced Materials Research;2014, Issue 886, p109 

    The behavior of flow stress of Al-Mn alloy during hot compression at the condition of έ=0.05,0.5,5,25s-1 while the temperature range from 300°C to 450°C was studied by Gleblee-3500. The results show that the Al-Mn alloy possess the remarkable characteristic of a peak stress, followed by...

  • Hot Deformation Behavior of Alloy 800H at Intermediate Temperatures: Constitutive Models and Microstructure Analysis. Cao, Y.; Di, H.; Misra, R.; Zhang, Jiecen // Journal of Materials Engineering & Performance;Dec2014, Vol. 23 Issue 12, p4298 

    The hot deformation behavior of a Fe-Ni-Cr austenitic Alloy 800H was explored in the intermediate temperature range of 825-975 °C and strain rate range of 0.01-10 s. The study indicates that dynamic recrystallization (DRX) occurred at 875-975 °C for strain rates of 0.01-0.1 s and adiabatic...

  • Study on the creep properties and microstructures of EW75 alloy. Yongjun Li; Xinggang Li; Kui Zhang // Applied Mechanics & Materials;2014, Issue 633-634, p133 

    The creep properties and microstructures of the aged (220°C, 6h) EW75 magnesium alloy at different temperature and of stress conditions were studied. The experimental results show that, the deformation temperature and deformation rate have visible influence on flow stress curve of EW75 alloy....

  • Evolution of Microstructure and Texture During Deformation and Recrystallization of Heavily Rolled Cu-Cu Multilayer. Suresh, K.; Rollett, A.; Suwas, Satyam // Metallurgical & Materials Transactions. Part A;Aug2013, Vol. 44 Issue 8, p3866 

    A Cu-Cu multilayer processed by accumulative roll bonding was deformed to large strains and further annealed. The texture of the deformed Cu-Cu multilayer differs from the conventional fcc rolling textures in terms of higher fractions of Bs and RD-rotated cube components, compared with the...

  • Deformation Microstructures of Mg-3Al-1Zn Magnesium Alloy Compressed Over Wide Regions of Temperature and Strain Rate. Zhou, Jia; Li, Luo-xing; Liu, Bo; Liu, Yang-sheng // Journal of Materials Engineering & Performance;Feb2011, Vol. 20 Issue 1, p133 

    Hot compression tests of Mg-3Al-1Zn magnesium alloy were performed at temperatures between 300-500 °C and strain rates between 0.03 and 90 s. Dynamic recrystallization of the alloy is developed by the necklace mechanism. At the temperature of 300 °C, structures are fully dynamic...

  • The Tensile Response of a Fine-Grained AA5754 Alloy Produced by Asymmetric Rolling and Annealing. Jin, H.; Lloyd, D. J. // Metallurgical & Materials Transactions. Part A;Mar2004, Vol. 35 Issue 3A, p997 

    Asymmetric rolling (ASR) followed by annealing has been used to produce very fine grain sizes in the commercial Al-3 wt pct Mg alloy, AA5754. The appropriate rolling and annealing practice can produce grain sizes as small as 1 µm, and the tensile response of this fine-grained material has...

  • Study of the effect of cyclic strain reversal on the interactions between SRX and PPT in the microalloyed austenite during hot rolling process. Muszka, Krzysztof; Graca, Paulina; Simm, Thomas; Palmiere, Eric // Key Engineering Materials;2014, Vol. 622-623, p1023 

    In the present work cyclic torsion test was used to simulate hot plate rolling process in order to study the effect of strain reversal on non-recrystallisation temperature using unalloyed and microalloyed austenite model alloys. It was found that the amount of strain reversal directly influences...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics