TITLE

Laser metal deposition defined

AUTHOR(S)
Locke, David; Candel-Ruiz, Antonio
PUB. DATE
November 2010
SOURCE
Industrial Laser Solutions;Nov/Dec2010, Vol. 25 Issue 6, p6
SOURCE TYPE
Periodical
DOC. TYPE
Article
ABSTRACT
The article presents an overview on the advantages of laser metal deposition (LMD), a generative laser procedure. The workpiece properties can be aimed for improvement by systematically combining or refining materials with the use of LMD. In addition, LMD produces a metallurgical bond that permanently binds the deposited metal onto the base material, making the best possible adhesion.
ACCESSION #
55381518

 

Related Articles

  • Effect of Scanning Speed on Material Efficiency of Laser Metal Deposited Ti6Al4V. Akinlabi, Esther T.; Mahamood, Rasheedat M.; Shukla, Mukul; Pityana, Sisa. // World Academy of Science, Engineering & Technology;2012, Issue 71, p1531 

    The study of effect of laser scanning speed on material efficiency in Ti6Al4V application is very important because unspent powder is not reusable because of high temperature oxygen pick-up and contamination. This study carried out an extensive study on the effect of scanning speed on material...

  • Selective Laser Sintering of PZT Ceramic Powders. Gureev, D. M.; Ruzhechko, R. V.; Shishkovskiı, I. V. // Technical Physics Letters;Mar2000, Vol. 26 Issue 3, p262 

    Conditions for the selective laser-induced layer sintering of a stoichiometric mixture of PbO, ZrO[sub 2], and TiO[sub 2] powders with the formation of bulk PZT ceramic articles were studied. The laser processing allows articles of the PZT ceramics to be obtained immediately in the course of...

  • Tailoring the chemical behavior of aluminum for selective etching by laser interference metallurgy. D'Alessandria, M.; M�cklich, F. // Applied Physics A: Materials Science & Processing;Feb2010, Vol. 98 Issue 2, p311 

    The chemical behavior of aluminum modified by laser interference metallurgy (LIMET) is investigated. LIMET allows the single-step creation of periodic patterns with a well defined long-range order on material surfaces. This technique can also induce local and periodical oxidation on aluminum...

  • Wear resistance of laser remelted thermally sprayed coatings. Surzhenkov, Andrei; Kulu, Priit; Tarbe, Riho; Mikli, Valdek; Sarjas, Heikki; Latokartano, Jyrki // Estonian Journal of Engineering;2009, Vol. 15 Issue 4, p318 

    Advantages of hard coatings and deposition technologies such as HVOF have opened new opportunities for the production of wear parts operating in an abrasive environment. Thermally sprayed hardmetal coatings are widespread in industrial applications for wear, but not usable under impact wear...

  • Droplet distributions from melt displacement and ejection mechanism during Al ns-laser ablation and deposition experiments: Influence of laser spot position. Cultrera, L.; Lorusso, A.; Maiolo, B.; Cangueiro, L.; Vilar, R.; Perrone, A. // Journal of Applied Physics;2014, Vol. 115 Issue 9, p093102-1 

    Experimental observations of the angular distribution of droplets during laser ablation and deposition of Al thin films are presented and discussed. The experimental results, obtained by simply moving the laser spot position with respect to the rotation axis of the target, allow clarification of...

  • A Novel Method to Dicing Anodically Bonded Silicon Glass MEMS Wafers Based on UV Laser Technique. Zhisheng Jing; Zelong Zhou; Chen Mei; Xiangyong Su; Zhuo Yang; Yi Tao // Applied Mechanics & Materials;2014, Issue 511-512, p3 

    UV laser dicing has many advantages such as mechanical stress-free and dicing shape-free, but it is seldom used to dice multi-layer MEMS wafers because of the deposition of a lot of debris and heat affected zones around the dicing lines. In this paper, a novel UV laser dicing method for...

  • `Light touch' leads to sticky solution. Machlis, Sharon // Design News;5/23/94, Vol. 50 Issue 10, p13 

    Reports that researchers at Israel's Technion Research and Development Foundation conducted experiments which showed that lasers may better prepare materials for adhesive joining than conventional processes like chemical etching or blasting. Advantages of using lasers over other processes;...

  • Design freedom at last? Blackman, Greg // Electro Optics;Jun/Jul2008, Issue 194, p16 

    The article examines the process used in laser sintering technology and its development. The technology is being utilised to engineer medical implants and manufacture customised dental caps. It refers to laser sintering as a generalised term for a group of processes, such as selective laser...

  • Element Distribution in Silicon Refining: Thermodynamic Model and Industrial Measurements. Næss, Mari; Kero, Ida; Tranell, Gabriella; Tang, Kai; Tveit, Halvard // JOM: The Journal of The Minerals, Metals & Materials Society (TM;Nov2014, Vol. 66 Issue 11, p2343 

    To establish an overview of impurity elemental distribution among silicon, slag, and gas/fume in the refining process of metallurgical grade silicon (MG-Si), an industrial measurement campaign was performed at the Elkem Salten MG-Si plant in Norway. Samples of in- and outgoing mass streams,...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics