TITLE

Polycrystals under applied loads: Second-order grain statistics

AUTHOR(S)
Turner, Joseph A.; Ghoshal, Goutam
PUB. DATE
July 2010
SOURCE
Applied Physics Letters;7/19/2010, Vol. 97 Issue 3, p031907
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The authors report results for the second-order statistics of the effective elastic moduli of polycrystals as a function of applied stress. These results are indicative of scattering behavior that occurs in such materials at ultrasonic frequencies. Numerical examples are given for materials of general interest with cubic symmetry subject to an applied uniaxial stress. The results suggest that the second-order statistics (scattering) may be more significantly affected than the first-order statistics (wave speed) with application of load for some materials. This work may be useful for development of techniques for monitoring changes in stress of loaded structures.
ACCESSION #
52479423

 

Related Articles

  • An Empirical Approach to Correlating Thermo-Mechanical Fatigue Behaviour of a Polycrystalline Ni-Base Superalloy. Whittaker, Mark; Lancaster, Robert; Harrison, William; Pretty, Christopher; Williams, Stephen // Materials (1996-1944);Nov2013, Vol. 6 Issue 11, p5275 

    Assessment of thermo-mechanical fatigue behaviour of the polycrystalline nickel alloy RR1000 reveals a significant effect of phase angle on fatigue life. The current paper explores two scenarios: the first where the mechanical strain range is held constant and comparisons of the fatigue life are...

  • A simple method for calculating strain distributions in quantum-wire structures. Faux, David A.; Downes, James R.; O’Reilly, Eoin P. // Journal of Applied Physics;8/15/1996, Vol. 80 Issue 4, p2515 

    Focuses on a study which presented a method for calculating the stress and strain distributions in quantum-wire structures. Theoretical background; Computations and results.

  • Ensuring the Continued Structural Airworthiness of the Airbus A300 Commercial Transport Aircraft. Collins, R A // Journal of Strain Analysis for Engineering Design (Professional ;1999, Vol. 34 Issue 6, p413 

    After consideration of the original certification basis of the Airbus A300 commercial transport aircraft, this paper considers typical industry procedures for the justification of the original design service goal, during which the principal structure of the aircraft is reasonably free from...

  • Stresses in TaSix films sputter deposited on polycrystalline silicon. Teal, V. L.; Murarka, S. P. // Journal of Applied Physics;6/1/1987, Vol. 61 Issue 11, p5038 

    Presents information on a study which examined stress in thin tantalum silicide[sub x] films sputtered on polycrystalline silicon as a function of temperature. Methodology of the study; Results and discussion; Conclusions.

  • Interdependence of magnetic properties and intrinsic stress in mono- and polycrystalline thin nickel films. Shih, C. Y.; Bauer, C. L.; Artman, J. O. // Journal of Applied Physics;11/15/1988, Vol. 64 Issue 10, p5428 

    Studies the interdependece of magnetic properties and intrinsic stress in mono- and polycrystalline thin nickel films. Characterization of the microstructure of both mono- and polycrystalline films; Interpretation of the saturation magnetization; Measurement of the intrinsic stresses in the...

  • Size effects of nanoindentation creep. H. Li; A. H. W. Ngan // Journal of Materials Research;Feb2004, Vol. 19 Issue 2, p513 

    The size effects on indentation creep were studied on single-crystal Ni3Al, polycrystalline pure Al, and fused quartz samples at room temperature. The stress exponents were measured by monitoring the displacement during constant indentation loads after correction for thermal drift effects. The...

  • Stresses in sputtered Ti-Si multilayers and polycrystalline silicide films. Wessels, P. J. J.; Jongste, J. F.; Janssen, G. C. A. M.; Mulder, A. L.; Radelaar, S.; Loopstra, O. B. // Journal of Applied Physics;5/15/1988, Vol. 63 Issue 10, p4979 

    Presents information on a study which investigated the stresses in sputtered titanium-silicon multilayers and polycrystalline silicide films. Significance of titanium disilicide; Model for stress in titanium silicon multilayers; Determination of poisson's ratio; Stresses due to rapid thermal...

  • Materials Science Under Extreme Conditions of Pressure and Strain Rate. Remington, B. A.; Bazan, G.; Belak, J.; Bringa, E.; Colvin, J. D.; Edwards, M. J.; Glendinning, S. G.; Kalantar, D. H.; Kumar, M.; Lasinski, B. F.; Lorenz, K. T.; McNaney, J. M.; Pollaine, S. M.; Rowley, D.; Stölken, J. S.; Weber, S. V.; Wolfer, W. G.; Caturla, M.; Ivanov, D. S.; Zhigilei, L. V. // Metallurgical & Materials Transactions. Part A;Sep2004, Vol. 35 Issue 9, p2587 

    Solid-state dynamics experiments at very high pressures and strain rates are becoming possible with high-power laser facilities, albeit over brief intervals of time and spatially small scales. To achieve extreme pressures in the solid state requires that the sample be kept cool, with Tsample <...

  • Pressure derivatives of the elastic moduli of a polycrystalline aggregate of hexagonal metal: Calculations using monocrystal elastic-constant pressure derivatives. Ramji Rao, R.; Janardhana, V. // Journal of Applied Physics;6/1/1985, Vol. 57 Issue 11, p5095 

    Presents a study which calculated the pressure derivatives of bulk, shear and Young's moduli, and of the Poisson's ration of a number of polycrystalline aggregate of hexagonal metal. Previous studies on the calculation of the elastic properties of a polycrystal from the elastic moduli and their...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics