TITLE

The Fabrication Drawing

AUTHOR(S)
Robertson, Chris
PUB. DATE
September 2001
SOURCE
Printed Circuit Design;Sep2001, Vol. 18 Issue 9, p44
SOURCE TYPE
Trade Publication
DOC. TYPE
Article
ABSTRACT
Part III. Presents information on fabrication drawing of circuits. Description of the surface finish process; Information on silkscreen aspect ratio; Details on the routing process.
ACCESSION #
5118525

 

Related Articles

  • Fab Trends: Are Europe and Asia leading the way? Haavind, Robert // Solid State Technology;Mar2000, Vol. 43 Issue 3, p8 

    Focuses on the fabricating technology used in semiconductor industries. Use of standard chips or discretes in semiconductor fabricating plants; Standards for making microprocessors; Combination of analog with digital circuitry; Trends in integrated circuits.

  • Thermo-Mechanical Failure Criterion at the Micron Scale in Electronic Devices. Yosibash, Z.; Adan, O.; Schneck, R.; Atlas, H. // International Journal of Fracture;Jul2003, Vol. 122 Issue 1/2, p47 

    Thermo-mechanical failures may occur in the passivation layer of micro-electronic devices during the fabrication process. These are in form of cracks which initiate at keyhole corners. In order to predict and eventually prevent these cracks a failure criterion is presented, based on an average...

  • Improving FABRICATION YIELDS by Design. Khan, Zulki // Printed Circuit Design & Manufacture;Apr2008, Vol. 25 Issue 4, p24 

    The article focuses on the improvement of printed circuit board (PCB) fabrication yields. It discusses the importance of the fabrication drawing, which is composed of notes, mechanical dimensions/drawings, stack up callouts and a drill chart. It cites the use of gold fingers, such as cables and...

  • Designing MMIC Distributed Amplifiers. Penn, John // Microwaves & RF;Nov2007, Vol. 46 Issue 11, p61 

    The article focuses on designing monolithic-microwave-integrated-circuit (MMIC) distributed amplifiers. It focuses on fabricating a classic broadband amplifier design with new PHEMT devices that provide improved performance over the same MMIC amplifier. The early design was tested at cryogenic...

  • Prototype Fabrication of Field-Programmable Digital Filter LSIs Using Multiple-Valued Current-Mode Logic -- Device Scaling and Future Prospects -- . Degawa, Katsuhiko; Aoki, Takafumi; Higuchi, Tatsuo // Journal of Multiple-Valued Logic & Soft Computing;2005, Vol. 11 Issue 5/6, p545 

    This paper presents prototype design and fabrication of Field-Programmable Digital Filter (FPDF) LSIs, which employ carry-propagation-free redundant arithmetic algorithms for faster operation and Multiple-Valued Current-Mode Logic (MV-CML) for high-density low-power implementation. The original...

  • Direct Sub-100-nm Patterning of an Organic Low-k Dielectric for Electrical and Optical Interconnects. Catchmark, Jeffrey M.; Lavallee, Guy P.; Rogosky, Michael; Youngchul Lee // Journal of Electronic Materials;Mar2005, Vol. 34 Issue 3, pL12 

    Low-k dielectric materials compatible with copper interconnect fabrication processes extending to the sub-50-nm technology nodes are desired for high speed integrated circuit (IC) fabrication. We demonstrate that bisbenzocyclobutene (BCB), an organic low-k dielectric material, can be patterned...

  • NAND teeters on the brink. Manners, David // Electronics Weekly;11/15/2006, Issue 2265, p12 

    The article reports that NAND flash manufacturers are building massive capacity amid the collapsing market. The concern is whether the growing demand can absorb the amount of capacity being thrown at the market. The Intel/Micron joint venture is currently bringing up three 300mm fabs for NAND...

  • On-Chip Passive Devices Technology: Component's Characteristics, Fabrication and Commercialization. Mirzaee, Hossein; Pourzaki, Abbas // International Review on Computers & Software;May2011, Vol. 6 Issue 3, p434 

    Product miniaturization with progressively decreases costs, because of increasing consumer demands in Computers, Telecommunications, Instrumentation & Test Equipment, Military & Aerospace, and Consumer & Automotive. In this paper, characteristics of passive components such as resistors,...

  • Fabrication Influences on High-Frequency PCB ELECTRICAL PERFORMANCE. COONROD, JOHN // Printed Circuit Design & Fab: Circuits Assembly;Sep2013, Vol. 30 Issue 9, p28 

    The article focuses on the influence of fabrication to the performance of high-frequency printed-circuit board (PCB). It mentions that the thickness of the circuit board has a major role on different issues related to impedance control in PCB, saying that material thickness of PCB can also...

Share

Read the Article

Courtesy of NEW JERSEY STATE LIBRARY

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics