TITLE

An Upper Bound Solution for Closed Die Sinter Forging of Hexagonal Shapes at High Speed

AUTHOR(S)
Sharma, Abhay Kumar; Ranjan, R. K.; Bajpai, V. K.
PUB. DATE
July 2008
SOURCE
International Journal of Mechanics & Solids;2008, Vol. 3 Issue 2, p185
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The paper reports on an investigation into the various aspects of closed die forging of hexagonal powder preforms, which have been compacted and sintered from atomized powder. It is found that for certain dimensional ratios of the preform the die pressure is minimum. An attempt has been made for the determination of the die pressures developed during the closed die forging of hexagonal powder preform at high speed by using an upper bound approach. The results so obtained are discussed critically to illustrate the interaction of various process parameters involved and are presented graphically.
ACCESSION #
47081868

 

Related Articles

  • Influence of material flow constraints during cold forming on the deformation and densification behaviour of hypoeutectoid P/M steel ring preforms. Chandramouli, R.; Pandey, K. S.; Kandavel, T. K.; Ashokkumar, T.; Shanmugasundaram, D. // International Journal of Advanced Manufacturing Technology;Jan2007, Vol. 31 Issue 9/10, p926 

    The deformation and densification behaviour of sintered hypo-eutectoid steel ring preforms with carbon contents of 0.35% and 0.65%, under cold axial deformations, have been studied in order to understand the influence of various forming parameters such as flow stress and percentage axial height...

  • Cold forging of sintered hollow polygonal disks with barreling. Das, P.; Sutradhar, Goutam; Chakraborty, T.; Patra, S.; Mitra, M. // Journal of Materials Science;May2008, Vol. 43 Issue 9, p3180 

    The forging of sintered metal-powder performs creates a lot of interest throughout the world as one of the most economic method of manufacturing techniques. This process becomes more popular due to its simplicity and flexibility. During compression of regular polygonal disk between a pair of...

  • Sintering Characteristics of Indian Chrome Ore Fines. Nandy, Bikash; Chaudhury, Manoj; Paul, Jagannath; Bhattacharjee, D. // Metallurgical & Materials Transactions. Part B;Oct2009, Vol. 40 Issue 5, p662 

    Chrome ore concentrate consists of high-temperature melting oxides such as Cr2O3, MgO, and Al2O3. The presence of these refractory constituents makes the ore a very high melting mineral. Hence, it is difficult to produce sinter from chrome ore by a pyrometallurgical route. Currently, chrome ore...

  • Roll Design Method of Single--Stage Profile Ring Rolling based on Modified UVDET. Byung-Min Kim; Kyung-Hun Lee // Key Engineering Materials;2014, Vol. 622-623, p1008 

    The aim of this study is to suggest the die design method for single-profile ring rolling in the production of a large scale welding neck flange, based on the modified uniform volume distribution element technique (UVDET). UVDET is presented as the ratio of volume change of ring blanks to that...

  • Method for producing twist drills by extrusion using a three-slide forging press. Bulzak, Tomasz; Tomczak, Janusz; Pater, Zbigniew // Key Engineering Materials;2014, Vol. 622-623, p129 

    The study presents a new method, developed by the authors, for producing twist drills by extrusion using a three-slide forging press. The method consists in using two sectional dies with specially shaped impressions that allow the removal of a ready drill from the die without unscrewing. The...

  • An experimental and numerical investigation into forming force reduction in precision gear forging. Politis, Nicholas J.; Politis, Denis J.; Davies, Catrin M.; Lin, Jianguo; Dean, Trevor A. // Key Engineering Materials;2014, Vol. 622-623, p165 

    A significant factor in the cost of industrial machinery for precision forging is the maximum load required to fully forge the final shape of components. Typically in a precision forging process, the required load increases greatly towards the end of the stroke. This study focuses on reducing...

  • Sensitivity analysis of process parameters for developing an improved open die forging process. Yufeng Cheng; Xiaoguang Yang; Qi Lu; Chao Voon Samuel Lim; Aijun Huang // Key Engineering Materials;2014, Vol. 622-623, p231 

    Open die hot forging has a wide industrial application on deforming ingot into billet with desired dimension and qualified internal microstructure. An example open die forging process of Ti-6Al-4V ingot is selected herein. A 3D FE-based numerical method was used to investigate the open die...

  • Ductility and Impact Resistance of Powder-Metallurgical Molybdenum-Rhenium Alloys. Leichtfried, Gerhard; Schneibel, Joachim H.; Heilmaier, Martin // Metallurgical & Materials Transactions. Part A;Oct2006, Vol. 37 Issue 10, p2955 

    Mo-Re alloys containing between 5 and 47.5 wt pct Re were fabricated from Mo and Mo-Re powders by sintering and hot radial forging. The mechanical properties of as-forged, stress-relieved, and recrystallized specimens were examined. Up to a concentration of 41 wt pet Re, the Charpy...

  • Influence of eccentric arrangement of the die for the temperature distribution in the sample during the pressure-assisted induction sintering (PAIS). Siemiaszko, Dariusz; Szykut, Marek // Key Engineering Materials;2014, Vol. 622-623, p514 

    In this work, the pressure-assisted induction sintering (PAIS) method, is being presented. The specimens (a cylindrical shape, diameter of 50 mm, height of 10 mm) was heated by a induction coil with heating speed of about 220 K/s to temperature 800°C, 850°C, 900°C, 950°C and...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics