TITLE

Düzlemine Dik Doğrultuda Yüklenmiş Tabakalı Kompozit Levhalarda Elasto-Plastik Gerilme Analizi

AUTHOR(S)
Turan, Kadir; Gür, Mustafa
PUB. DATE
June 2009
SOURCE
Firat University Journal of Engineering;Jun2009, Vol. 21 Issue 1, p63
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
In this study elastic - plastic stress analysis is examined in a laminated thermoplastic composite plates under transverse loading conditions. For solving problem ANSYS program,which is used finite element method, is used. The effect of ply array, fiber orientation angle, supported type and plate dimension variation on elastic - plastic and residual stresses of laminated thermoplastic composite plates are investigated. Elastic-plastic analysis is made three steps. In the first step of the analysis the yielding loads are finding each plate and in the second step elastic-plastic stresses are obtained from yield load + 0.01 MPa load increment for each plate. The last step is made for obtained residual stresses and the load on the plate is removed. Obtained elastic-plastic and residual stresses are illustrated graphs in this study.
ACCESSION #
43565692

 

Related Articles

  • Investigation of Residual Stresses on Transversally Loaded Thermoplastic Composite Plates. Turan, Kadir; Kaman, Mete Onur; Gür, Mustafa // Turkish Journal of Science & Technology;Jun2009, Vol. 4 Issue 1, p31 

    In this study, elastic-plastic stress analysis is performed in thermoplastic plate, which has symmetric and antisymmetric bonded laminated, with circular or square hole in the centre of plate. Elastic-plastic stress analysis is carried out on the laminated composite plate by using finite element...

  • Elasto-plastic stress analysis of thick-walled FGM pipes. Figueiredo, Fabio; Borges, Lavinia; Rochinha, Fernando // AIP Conference Proceedings;2/15/2008, Vol. 973 Issue 1, p147 

    The paper is concerned with quasi-static deformation processes of elastic-plastic FGM structures. It is assumed that the structures undergo small strain and the material properties of the graded layer are modeled by the modified rule of mixtures approximation. The elastic domain for ductile...

  • Stress monitoring and analysis using lock-in thermography. George, Sheri; Goravar, Shivappa; Mishra, Dedashi; Shyamsunder, M. T.; Sharma, Prafull; Padmashree, G. K.; Kumar, P. Sanjeev; Bremond, Pierre; Mukherjee, Kaveri // Insight: Non-Destructive Testing & Condition Monitoring;Sep2010, Vol. 52 Issue 9, p470 

    An advanced non-destructive evaluation technique based on a thermal method and lock-in principles, known as thermoelastic stress analysis (TSA), is proposed for accurate stress measurements. Traditionally, strain gauges mounted on components of interest are used to measure stresses indirectly....

  • Multipass low-plasticity burnishing induced residual stresses: three-dimensional elastic—plastic finite element modelling. Zhuang, W.; Wicks, B. // Proceedings of the Institution of Mechanical Engineers -- Part C;Jun2004, Vol. 218 Issue 6, p663 

    Low-plasticity burnishing (LPB) is a surface modification process involving complex cyclic plastic deformation that results in the development of a deep residual stress field. In order to achieve an optimal LPB-induced residual stress field for the geometry appropriate to the aircraft engine...

  • Effects of thermomechanical treatments on microstructure and mechanical behavior of HCS / LCS bimetal. Xingjian Gao; Zhengyi Jiang; Dongbin Wei; Huijun Li; Sihai Jiao; Jingtao Han // Advanced Materials Research;2014, Issue 922, p183 

    A high carbon steel (HCS) and low carbon steel (LCS) bimetal was fabricated by centrifugal composite casting. Two different thermomechanical treatments (TMT1 and TMT2) were employed to improve the mechanical properties of the bimetal. TMT1 process includes 60% of overall reduction by hot...

  • Finite Element Analysis of Residual Stresses in Metallic Coatings through a Compound Casting. Yongning Liu; Yiqing Chen; Rolfe, Bernard F.; Chunhui Yang // Applied Mechanics & Materials;2014, Issue 553, p48 

    Al and Mg alloys are widely used in industry as main lightweight alloys. They have excellent properties, such as low density, high ductility, and high specific strength, and so on. Generally speaking, Mg alloys are better than Al alloys. However the corrosion of Mg alloys is much more difficult...

  • Residual Stress Study of Autofrettaged Barrel under Impulsive Loading. Pu Qu; Qiang Li; Shufang Yang // Applied Mechanics & Materials;2014, Issue 518, p144 

    An analysis model of barrel was established for rapid-firing gun by using the thermal-structure direct coupling analysis method. As a solving tactics, finite element method was employed to analyze the influence of degree of autofrettage on the residual stress of the tube under impact load caused...

  • Analytical modeling of edge effects on the residual stresses within the film/substrate systems. I. Interfacial stresses. Zhang, X. C.; Xu, B. S.; Wang, H. D.; Wu, Y. X. // Journal of Applied Physics;12/1/2006, Vol. 100 Issue 11, p113524 

    Several analytical models have been developed to derive the closed-form solutions for the residual stresses at the interface when a film was overlaid on a substrate. In these models, the film edge effects on the interfacial stresses were analyzed. However, some of the existing models do not...

  • A resonant method for determining the residual stress and elastic modulus of a thin film. Ma, Shujun; Wang, Shiliang; Iacopi, Francesca; Huang, Han // Applied Physics Letters;7/15/2013, Vol. 103 Issue 3, p031603 

    By measuring the resonant frequencies of the first two symmetric vibration modes of a circular thin-film diaphragm and solving the Rayleigh-Ritz equation analytically, the residual stress and elastic modulus of the film were determined simultaneously. The results obtained employing this method...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics