TITLE

Designing Welds to Avoid Fatigue Failure

PUB. DATE
July 2009
SOURCE
Welding Journal;Jul2009, Vol. 88 Issue 7, p62
SOURCE TYPE
Trade Publication
DOC. TYPE
Article
ABSTRACT
The article offers information on the significance of welding design to avoid fatigue failure of materials. It is vital for an individual to consider the performance of a weld under the cyclic load because when it is subjected to cyclic tensile or stress, there is a likelihood that it may fail. Because of its significance, various organizations developed standards including the American Institute of Steel Construction and the American Association of State Highway and Transportation Officials.
ACCESSION #
42957958

 

Related Articles

  • The hot formability of an Al-Cu-Mg-Fe-Ni forging disk. Aghaie-Khafri, M.; Zargaran, A. // JOM: The Journal of The Minerals, Metals & Materials Society (TM;Feb2010, Vol. 62 Issue 2, p37 

    The high temperature formability of AA2618-T61 forged disk was studied by means of tensile test over temperatures and strain rates ranging from 100 to 400°C and 3 × 10−5 −3 × 10−3 s−1, respectively. The constitutive equations of the material were calculated...

  • The Effect of Material Cleanliness on Dynamic Damage Evolution in 10100 Cu. Thissell, W. Richards; Zurek, Anna K.; Macdougall, Duncan A. S.; Miller, David; Everett, Richard; Geltmacher, Andrew; Brooks, Robert; Tonks, Davis // AIP Conference Proceedings;2002, Vol. 620 Issue 1, p475 

    Two different plates of 10100 Cu (> 99.99 % Cu) were incipiently failed using flyer plate impact in a gas gun equipped with soft recovery. One plate has a grain size of 53 µm and the other, 63 µm. The cleanliness of the plates was assessed using the cold crucible melt technique. The...

  • Drop forging of HSLA steel with application of thermomechanical treatment. SKUBISZ, P.; ŁUKASZEK-SOŁEK, A.; SIŃCZAK, J.; BEDNAREK, S. // Archives of Civil & Mechanical Engineering (Oficyna Wydawnicza P;2008, Vol. 8 Issue 4, p93 

    Problems of realization of thermomechanical treatment for microalloyed-steel forgings are presented. The issue is discussed on the example of high-pressure-pump crankshaft. n the strength of numerical analysis results conditions for favourable strain and temperature distribution were determined....

  • Effect of Stress Ratio on High-Cycle Fatigue Properties of Ti-6Al-4V ELI Alloy Forging at Low Temperature. Yoshinori Ono; Tetsumi Yuri; Toshio Ogata; Saburo Matsuoka; Hideo Sunakawa // AIP Conference Proceedings;Jan2014, Vol. 1574, p23 

    The effect of the stress ratio R (the ratio of minimum stress to maximum stress) on the high-cycle fatigue properties of Ti-6Al-4V extra-low interstitial (ELI) alloy forging was investigated at 293 and 77 K. At 293 K, the fatigue strength at 107 cycles exhibited deviations below the modified...

  • Coupling Finite Element And Meshless Methods To Deal With Contact And Friction In Forging Processes. Guedes, Cristina Faria; César de Sá, José M. A. // AIP Conference Proceedings;2007, Vol. 908 Issue 1, p1507 

    In this work, a computational model based on a meshless method, the EFG method, was developed to simulate forging processes. The application of meshless methods in this type of forming processes opened new questions related to crucial aspects associated with the modelling of frictional effects...

  • Modeling The Interaction Effects Between Tools And The Work Piece For Metal Forming Processes. Franzke, Martin; Puchhala, Sreedhar; Dackweiler, Harald // AIP Conference Proceedings;2007, Vol. 908 Issue 1, p1489 

    In metal forming processes especially in cold forming, elastic deformation of the tools has a big impact on the final shape of the work-piece. Computation of such processes considering the plastic effects of the work-piece and elastic deformations of the tools at a time in a single FE model...

  • Numerical and Experimental Studies on Strain Distribution and Weld Line Movement in Stretch Forming of Tailor Welded Blanks. Panda, Sushanta Kumar; Kumar, D. Ravi // AIP Conference Proceedings;2007, Vol. 908 Issue 1, p1451 

    Use of laser welded blanks of multiple sheets of material which are referred to as Tailor Welded Blanks (TWB) is one of the current interests for automotive industries as it reduces manufacturing cost, weight of the vehicle and also improves the quality of the component. As the varieties of TWB...

  • Practical aspects of development of standards for calculating strength of vessels and apparatuses. Sukharnikova, I. // Chemical & Petroleum Engineering;Aug2011, Vol. 47 Issue 9/10, p679 

    The viewpoint of one of the developers of the collection of national standards GOST R 52857.1-2007 - GOST R 52857.12-2007 'Vessels and Apparatuses. Norms and Methods of Strength Calculation' on the problems of support for standards over their life cycle is elucidated and recommendations are...

  • Characteristics of Compressive Stress Distribution in High-Strength Concrete. Loov, Robert E. // ACI Structural Journal;Jul/Aug2009, Vol. 106 Issue 4, p561 

    The article discusses a paper about the characteristics of compressive stress distribution in high-strength concrete. The paper analyzed the test results from different experiments and will be referenced by standards committees and future researchers. A lower-bound solution appears correct as it...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics