High accuracy magnetic field measurements with a Hall probe

Schott, C.; Popovic, R.S.; Alberti, S.; Tran, M.Q.
June 1999
Review of Scientific Instruments;Jun99, Vol. 70 Issue 6, p2703
Academic Journal
Describes a silicon-based temperature stabilized axial Hall probe with an absolute accuracy of +/-40 ppm in the range from 0 to 6 T. Hall probe configuration; Magnetic field configuration; Calibration procedure.


Related Articles

  • Scanning Hall probe microscopy with shear force distance control. Schweinbo¨ck, Thomas; Weiss, Dieter; Lipinski, Martin; Eberl, Karl // Journal of Applied Physics;5/1/2000, Vol. 87 Issue 9, p6496 

    We describe a new type of scanning Hall probe microscope operating at room temperature for quantitative and noninvasive measurements of magnetic stray fields. The probe-sample distance is controlled by piezoelectrical detection of the shear forces acting on an oscillating cantilever. The Hall...

  • Understand probe-card measurement variations. Sekar, Chander M.; Scutoski, Henry P. // Test & Measurement World;Jan99, Vol. 19 Issue 1, p41 

    Describes how to use the Gage-R&R method to characterize probe-tip location using a probe-card analyzer. Two components of errors within a measurement process; Determination of a bias by comparing measured values to calibrate standards; Quantification of the measuring capability of an...

  • A calibration method of a radio frequency magnetic probe. Yang, J.G.; Choi, J.H.; Kim, B.C.; Yoon, N.S.; Hwang, S.M. // Review of Scientific Instruments;Sep99, Vol. 70 Issue 9, p3774 

    Demonstrates a simple calibration method of a radio frequency magnetic probe by utilizing a two port network analysis method. Measurement of the scattering parameters; Calculation of the magnetic field generated by the Helmholtz coil; Determination of probe sensitivity.

  • Coats checked without wear.  // Environmental Engineering;Mar2002, Vol. 15 Issue 1, p13 

    Evaluates the FN 1.6P Power Probe for use with the MiniTest 4100 series of coating thickness measurement instruments from ElektroPhysik. Features and functions of the device; Limitations of the device.

  • Electrical measurements with a SQUlD susceptometer. Wong, H. K. // Review of Scientific Instruments;Jun91, Vol. 62 Issue 6, p1664 

    We describe the design of a probe that can be inserted into a SQUID susceptometer (S.H.E. model VTS-805) for electrical measurements at variable temperature and high magnetic field. This top-loading probe allows multisample measurements and rapid sample replacement without disturbing the...

  • Calibration of magnetic probes in the vicinity of a conducting well. Howard, S. J.; Horton, R. D.; Hwang, D. Q.; Evans, R. W.; Brockington, S. J. // Review of Scientific Instruments;Feb2008, Vol. 79 Issue 2, p023503 

    Measuring magnetic fields near the edge of a plasma device can be complicated by the geometric effects of the ports through which such measurements are made. The primary effect is an attenuation of the magnetic field at the probe coil due to the field expanding into the finite sized conducting...

  • Noise Measurement of Interacting Ferromagnetic Particles with High Resolution Hall Microprobes. Komatsu, K.; L'Hôte, D.; Nakamae, S.; Ladieu, F.; Mosser, V.; Kerlain, A.; Konczykowski, M.; Dubois, E.; Dupuis, V.; Perzynski, R. // AIP Conference Proceedings;4/23/2009, Vol. 1129 Issue 1, p153 

    We present our first experimental determination of the magnetic noise of a superspin-glass made of <1 pico-liter frozen ferrofluid. The measurements were performed with a local magnetic field sensor based on Hall microprobes operated with the spinning current technique. The results obtained,...

  • NDT Inspections Exploiting Invariances on Scale Transformations. Ramos, Helena Geirinhas; Torres, João; Ribeiro, Artur L.; Rebello, João // AIP Conference Proceedings;2015, Vol. 1650 Issue 1, p327 

    The aim of this paper is to show the invariance on the giant magneto-resistor sensor (GMR) output response in the measurement of different plate thicknesses when the problem is resized. To resize the problem, two different probes were projected, implemented and tested: one, with all the...

  • Liquid helium level detector. Quine, Richard W.; Eaton, Sandra S.; Eaton, Gareth R. // Review of Scientific Instruments;Jun91, Vol. 62 Issue 6, p1647 

    A simple mechanical and electrical design is presented for a small probe for monitoring the level of liquid helium in experimental apparatus or storage Dewars.


Read the Article


Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics