TITLE

A piezotube scanner for atomic force microscopy in solution

AUTHOR(S)
Jianxun Mou; Gang Huang; Zhifeng Shao
PUB. DATE
July 1996
SOURCE
Review of Scientific Instruments;Jul96, Vol. 67 Issue 7, p2654
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Describes a piezotube scanner used in the atomic force microscope (AFM). Advantages of the design; Significance of the design for biological AFM.
ACCESSION #
4271734

 

Related Articles

  • Calibration of the torsional spring constant and the lateral photodiode response of frictional force microscopes. Feiler, Adam; Attard, Phil; Larson, Ian // Review of Scientific Instruments;Jul2000, Vol. 71 Issue 7 

    We present a direct one-step technique to measure the torsional spring constant of cantilevers used for lateral or friction measurements with the atomic force microscope. The method simultaneously calibrates the photodiode response to the angular deflection of the cantilever. It does not rely...

  • Characterization and optimization of scan speed for tapping-mode atomic force microscopy. Sulchek, T.; Yaralioglu, G. G.; Quate, C. F.; Minne, S. C. // Review of Scientific Instruments;Aug2002, Vol. 73 Issue 8, p2928 

    Increasing the imaging speed of tapping mode atomic force microscopy (AFM) has important practical and scientific applications. The scan speed of tapping-mode AFMs is limited by the speed of the feedback loop that maintains a constant tapping amplitude. This article seeks to illuminate these...

  • Three-dimensional beam tracking for optical lever detection in atomic force microscopy. Nakano, Katsushi; Yakimov, V.; Erlandsson, R. // Review of Scientific Instruments;Jan2000, Vol. 71 Issue 1 

    For the requirement to move a probe with respect to a large specimen like a silicon wafer, a three-dimensional beam tracking for optical lever force detection in atomic force microscopy has been developed. This beam tracking is not an approximate solution but an ideal solution in...

  • High Volume Single Molecule Force Spectroscopy Results.  // Labmate UK & Ireland;2011, Vol. 36 Issue 6, p15 

    The article reports on the results of the work from the Pharmaceutical Sciences Department of the Medical School at the University of Nebraska which used the JPK ForceRobot 300 system to extend studies applying the atomic force microscopy in the measurement of single molecule force spectroscopy.

  • Device for the determination of spring constants of atomic force microscope cantilevers and micromachined springs. Jericho, S. K.; Jericho, M. H. // Review of Scientific Instruments;Jun2002, Vol. 73 Issue 6, p2483 

    We describe a simple device for the calibration of atomic force microscope cantilevers and micromachined springs. The device measures the deflection of the cantilevers in response to known forces that are derived from calibrated macroscopic cantilever springs. We have used the device to...

  • Towards atomic force microscopy up to 100 MHz. Kawakatsu, H.; Kawai, S.; Saya, D.; Nagashio, M.; Kobayashi, D.; Toshiyoshi, H.; Fujita, H. // Review of Scientific Instruments;Jun2002, Vol. 73 Issue 6, p2317 

    An atomic force microscope for nanocantilevers measuring from a few 100 nm to a few µm in length was implemented. The natural frequencies of the nanocantilevers lie in the range of 1 MHz to 1 GHz, and optical detection schemes adapted to their size and frequency range was selected. A helium...

  • Atomic force microscope detector drift compensation by correlation of similar traces acquired at different setpoints. Kindt, Johannes H.; Thompson, James B.; Viani, Mario B.; Hansma, Paul K. // Review of Scientific Instruments;Jun2002, Vol. 73 Issue 6, p2305 

    The atomic force microscope measures surface topography by maintaining a certain cantilever deflection or vibration amplitude as the cantilever is scanned over a sample surface. The desired cantilever deflection or amplitude is referred to as the setpoint, and is maintained by moving the sample...

  • Nanoscale elasticity measurement with in situ tip shape estimation in atomic force microscopy. Yamanaka, Kazushi; Tsuji, Toshihiro; Noguchi, Atsushi; Koike, Takayuki; Mihara, Tsuyoshi // Review of Scientific Instruments;Jun2000, Vol. 71 Issue 6 

    For a quantitative evaluation of nanoscale elasticity, atomic force microscopy, and related methods measure the contact stiffness (or force gradient) between the tip and sample surface. In these methods the key parameter is the contact radius, since the contact stiffness is changed not only by...

  • Dynamics of damped cantilevers. Rast, S.; Wattinger, C.; Gysin, U.; Meyer, E. // Review of Scientific Instruments;Jul2000, Vol. 71 Issue 7 

    In atomic force microscopy cantilevers are used to detect forces caused by interactions between probing tip and sample. The minimum forces which can be detected with commercial sensors are typically in the range of 10[sup -12] N. In the future, the aim will be to construct sensors with improved...

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics