TITLE

High-temperature cylindrical specimen grip for biaxial loading

AUTHOR(S)
Lipetzky, P.; Dvorak, G.; Stoloff, N.
PUB. DATE
May 1996
SOURCE
Review of Scientific Instruments;May96, Vol. 67 Issue 5, p1989
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Reports on the development of a device for hot-gripping cylindrical specimens subjected to biaxial (tension/torsion) loading. Device description; Hot gripping; Load distribution; Torsional rigidity.
ACCESSION #
4271675

 

Related Articles

  • Elimination of loading reverberation in the split Hopkinson torsional bar. Xue, Q.; Shen, L.T.; Bai, Y.L. // Review of Scientific Instruments;Nov95, Vol. 66 Issue 11, p5298 

    Discusses the problem of loading reverberation and its effects on the post-mortem observations in experiments with split Hopkinson torsional bar (SHTB), one of the most widely used instruments for determining the mechanical behavior of materials under high strain rate loading. Effect of...

  • A torsional balance for the characterization of microNewton thrusters. Gamero-Castaño, Manuel // Review of Scientific Instruments;Oct2003, Vol. 74 Issue 10, p4509 

    Describes the performance of a torsional balance suitable for the study of microNewton thrusters. Basis of the design on flexural pivots and electrostatic forces; Proof of the usefulness of the balance by measuring the performance of two different electric propulsion accelerators.

  • Electrostatically suspended torsion pendulum. Willemenot, E.; Touboul, P. // Review of Scientific Instruments;Jan2000, Vol. 71 Issue 1 

    Reports on the design and performance of a torsion pendulum without a torsion wire. Vertical and horizontal suspension principle; Noise spectral density of the capacitive sensors; Angular acceleration spectrum; Variation of torsion stiffness of the free oscillating mode with the angular position.

  • On-ground investigation of space accelerometers noise with an electrostatic torsion pendulum. Willemenot, E.; Touboul, P. // Review of Scientific Instruments;Jan2000, Vol. 71 Issue 1 

    A torsion pendulum has been used to measure very weak forces that limit the resolution of highly sensitive space accelerometers. A new method is described to measure damping with a feedback loop. The main results are (i) an upper limit to time evolution of contact potential differences inside...

  • Comparison of electrostatic fins with piezoelectric impact hammer techniques to extend impulse calibration range of a torsional thrust stand. Pancotti, Anthony P.; Gilpin, Matthew; Hilario, Martin S. // Review of Scientific Instruments;Mar2012, Vol. 83 Issue 3, p035109 

    With the progression of high-power electric propulsion and high thrust-to-power propulsions system, thrust stand diagnostics require high-fidelity calibration systems that are accurate over a large-range of thrust levels. Multi-mode and variable Isp propulsion devices also require that a single...

  • Torsion of semi-auxetic rods. Teik-Cheng Lim // Journal of Materials Science;Nov2011, Vol. 46 Issue 21, p6904 

    A method for quantifying the overall Poisson's ratio of a rod undergoing torsional loading is proposed and applied for a concentrically compound rod with inner core and outer shell of similar shape but opposite Poisson's ratio signs. Results show that a concentric compound rod with auxetic core...

  • The mean stress influence on lifetime under high-cycle fatigue combined loading. Janoušek, J.; Balda, M.; Svoboda, J. // Applied & Computational Mechanics;Jun2013, Vol. 7 Issue 1, p31 

    This paper summarizes the results from the field of combined loading. This study builds on experiments that have been performed during the last ten years and provides information on sinusoidal in-phase stress components and tenseness distribution. Unfortunately, there is no exact method for...

  • Rail ton-miles week ending Aug. 31.  // Traffic World;9/16/96, Vol. 247 Issue 11, p50 

    Focuses on carloadings which originated on major railroads in the United States during the week ended August 31, 1996. Carloads originated by commodity group.

  • Loaders, parts & accessories marketplace.  // Pit & Quarry;Mar97, Vol. 89 Issue 9, p32 

    Lists loaders, loader parts and accessories in the United States. Atlas Copco Wagner Inc.; Caterpillar Inc.; LeTourneau Inc.; Hendrix Manufacturing Co.

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics