TITLE

On the growth of nanocrystalline grains in an aluminum-based amorphous alloy

AUTHOR(S)
Nakazato, Kazuki; Kawamura, Yoshihito
PUB. DATE
November 1993
SOURCE
Applied Physics Letters;11/8/1993, Vol. 63 Issue 19, p2644
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Examines the growth of nanocrystalline grains in an aluminum-based amorphous alloy. Discussion on differential scanning calorimetry and transmission electron microscopy; Estimation on the grain size of the grown aluminum; Implication of the grain growth process for the nuclei.
ACCESSION #
4250709

 

Related Articles

  • Crystallization Behaviour of Amorphous Al-Ni-Nd Alloy. Gögebakan, Musa; Gündes, Alaaddin // AIP Conference Proceedings;2007, Vol. 899 Issue 1, p606 

    In this study, crystallization behaviour of rapidly solidified Al85Ni5Nd10 alloy has been investigated by differential scanning calorimetry (DSC). Continuous heating DSC trace of amorphous Al85Ni5Nd10 alloy consisted of three exothermic peaks. This indicated that; crystallization of amorphous...

  • Kinetics of silicide formation in chromium-amorphous silicon multilayered films. Schlesinger, T.E.; Cammarata, R.C.; Prokes, S.M. // Applied Physics Letters;7/22/1991, Vol. 59 Issue 4, p449 

    Investigates the silicide formation in multilayered thin films and amorphous silicon by differential scanning calorimetry (DSC). Display of a large main peak associated with the silicide growth; Linear rate law followed by the growth kinetics; Inability of the DSC to induce an explosive...

  • The Sequence of Precipitation in the Al-Mg-Si-Cu Alloy AA6111. Xiang Wang; Esmaeili, Shahrzad; Lloyd, David J. // Metallurgical & Materials Transactions. Part A;Sep2006, Vol. 37 Issue 9, p2691 

    The precipitation behavior of the aluminum alloy AA6111 in the advanced stages of aging has been studied using differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and high-resolution TEM (HRTEM). The results have demonstrated the formation of various precipitate...

  • Variation of the microstructure of ingots of DC cast alloy 7050 during homogenization. Zhiqiang Cao; Yali Feng; Tingju Li; Jiachun Wang // Metal Science & Heat Treatment;Sep2010, Vol. 52 Issue 3/4, p179 

    The structure of ingots of aluminum alloy 7050 after casting and homogenization is studied by the methods of differential scanning calorimetry, light and scanning electron microscopy, and x-ray diffractometry.

  • Effects of short aging on thickening anisotropy of θ′ precipitate and mechanical properties of severe cold-rolled 2519A aluminum alloy plate. Xin-ming Zhang; Zhi-guo Gao; Yi-sheng Zhao // Journal of Materials Science;Mar2010, Vol. 45 Issue 5, p1401 

    The article discusses a study that performed short aging treatments to balance ultimate tensile strength (UTS) and ductility of severe cold-rolled (SCRed) 2519A aluminum alloy. A differential scanning calorimeter (DSC) was used to conduct experiments to identify an appropriate aging temperature....

  • Anomalous thermal effects in crystallization of hydrogenated amorphous alloys of the TiNi-TiCu system. Spivak, L. V.; Shelyakov, A. V. // Technical Physics Letters;Dec2009, Vol. 35 Issue 12, p1137 

    Several anomalous effects not reported previously for the interaction of hydrogen with amorphous alloys of the TiNi-TiCu system have been observed, including (i) the passage from one-to multistage mechanism of the transition from the amorphous to crystalline state in hydrogenated alloys, (ii) a...

  • Investigation of the structural transformations in the Al-Li-Cu-Mg (8090) alloy. Gaber, A.; Afify, N. // Applied Physics A: Materials Science & Processing;1997, Vol. 65 Issue 1, p57 

    The precipitation processes in quenched Al-2.4Li-1.16Cu-0.8Mg(wt.%) alloy (8090) from the solid solution state (T[sub q] =803 K) have been investigated via the Vickers microhardness measurements, scanning electron microscopy and differential scanning calorimetry. On the basis of Kissinger�s...

  • Optimization of homogenizing mode for aluminum alloy AA7075 using calorimetric and microstructural studies. Nayan, Niraj; Narayana Murty, S. Y. S.; Gotvind; Mittal, M. C.; Sinha, P. P. // Metal Science & Heat Treatment;Jul2009, Vol. 51 Issue 7-8, p330 

    Modes of heat treatment are developed for homogenizing cast structure of commercial aluminum alloy AA7075 with the aim of improving its process ductility. The temperature is optimized with the help of differential scanning calorimetry. Computations and studies of microstructure are used to...

  • Studies of homogenization of dc cast billets of aluminum alloy AA2014 by the methods of calorimetry and metallography. Nayan, Niraj; Narayana Murty, S. V. S.; Govind; Mittal, M. C.; Sinha, P. P. // Metal Science & Heat Treatment;Sep2010, Vol. 52 Issue 3/4, p171 

    Modes for heat treatment for homogenizing the cast structure and raising the processibility of alloy AA2014 are determined by empirical methods with the use of light microscopy. The time and temperature of annealing, which determine minimization of dendritic segregation and dissolution of...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics