TITLE

A high-power electron beam source based on the superemissive cathode

AUTHOR(S)
Hsu, T.-Y.; Gundersen, M.A.
PUB. DATE
November 1992
SOURCE
Applied Physics Letters;11/23/1992, Vol. 61 Issue 21, p2515
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Examines the high-powered electron beam source based on the superemissive refractory metal cathode. Effects of operational parameters on the electron beam generation; Definition of charge transfer efficiency; Effectiveness of pulse forming network in generating electron beams with square pulse.
ACCESSION #
4250574

 

Related Articles

  • Space-charge effects and current self-quenching in a metal/CdS/LaS cold cathode. Mumford, P.D.; Cahay, M. // Journal of Applied Physics;9/1/1998, Vol. 84 Issue 5, p2754 

    Analyzes the importance of space-charge effects in a cadmium sulfide/lanthanum sulfide cold cathode. Use of the Monte Carlo description of electron transport; results of the space-charge effects; Information on the limiting anode current density.

  • The spatial distribution of small signal gain in a segmented hollow cathode discharge laser. Adamowicz, T.M.; Donkó, Z.; Szalai, L.; Rózsa, K.; Kwaśniewski, W. // Applied Physics B: Lasers & Optics;1997, Vol. 65 Issue 4/5, p613 

    We present measurements of the spatial distribution of the small signal gain in the cross section of a longitudinally segmented hollow cathode discharge. This configuration proved to be the most efficient for pumping different cathode sputtered metal ion laser transitions excited by thermal...

  • WELDS FORMATION IN EBW OF HEAT-RESISTANT STEELS OF THE GRADES 10Kh9MFBA AND 10Kh12M. NESTERENKOV, V. M.; KRAVCHUK, L. A.; ARKHANGELSKY, Yu. A.; BONDAREV, A. A. // Paton Welding Journal;Jun2013, Issue 6, p38 

    The influence of both the conditions of electron beam welding of heat-resistant steels 10Kh12M and 10Kh9MFBA 30 mm thick without preheating and also the spatial arrangement of electron beam relatively to the part being welded on weld formation and tendency to crack formation was investigated. It...

  • MECHANICAL PROPERTIES OF JOINTS OF HEAT-RESISTANT 10Kh12M, 10Kh9MFBA GRADE STEELS, MADE BY ELECTRON BEAM WELDING. NESTERENKOV, V. M.; KRAVCHUK, L. A.; ARKHANGELSKY, Yu. A. // Paton Welding Journal;Sep2013, Issue 9, p37 

    In the course of development of works on the technology of electron beam welding of special steels the investigations of properties of the joints of heat-resistant 10Kh12M, 10Kh9MFBA grade steels of δm = = 30 mm thickness, made by single- and multipass electron beam welding using horizontal...

  • Microstructure Evolution and Composition Control During the Processing of Thin-Gage Metallic Foil. Semiatin, S.; Gross, M.; Matson, D.; Bennett, W.; Bonham, C.; Ustinov, A.; Ballard, D. // Metallurgical & Materials Transactions. Part A;Dec2012, Vol. 43 Issue 12, p4819 

    The manufacture of thin-gage superalloy and gamma-titanium-aluminide foil products via near-conventional thermomechanical processing and two different vapor-deposition methods was investigated. Thermomechanical processing was based on hot-pack rolling of plate and sheet. Foils of the superalloy...

  • Stray Grain Formation and Solidification Cracking Susceptibility of Single Crystal Ni-Based Superalloy CMSX-4. ANDERSON, T. D.; DUPONT, J. N. // Welding Journal;Feb2011, Vol. 90 Issue 2, p27S 

    The stray grain formation behavior and susceptibility to solidification cracking in autogenous welds on single crystal alloy CMSX-4 have been investigated. Welds were prepared using the electron beam (EB) and gas tungsten arc welding (GTAW) processes. The stray grain area fraction and cracking...

  • Microstructures and Properties for a Superalloy Powder Mixture Process by Electron Beam Melting. Hernandez, J.; Murr, L. E.; Amato, K. N.; Martinez, E.; Shindo, P. W.; Terrazas, C. A.; Rodriguez, E.; Medina, F.; Wicker, R. B.; Li, S. J.; Cheng, X. Y.; Yang, F. // Journal of Materials Science Research;Jul2012, Vol. 1 Issue 3, p124 

    The microstructure and residual hardness for solid components of 2-phase TiAl (Ti-48Al-2Nb-2Cr in a/o) and Inconel 625 (Ni-22Cr-6Mo-2Nb in a/o) fabricated by electron beam melting (EBM) were compared with a 10:1 blend of TiAl: alloy 625 pre-alloyed powders producing a complex alloy having the...

  • INFLUENCE OF WELD POOL GEOMETRY ON STRUCTURE OF METAL OF WELDS ON HIGH-TEMPERATURE NICKEL ALLOY SINGLE CRYSTALS. YUSHCHENKO, K.A.; GAKH, I.S.; ZADERY, B.A.; ZVYAGINTSEVA, A.V.; KARASEVSKAYA, O.P. // Paton Welding Journal;May2013, Issue 5, p45 

    The main defect, which prevents realization of the advantages of high-temperature nickel alloy single crystals in production of welded assemblies and parts of gas-turbine engine, are stray grains in the weld metal. The objective of this work was studying the features of weld metal structure,...

  • Open-Cellular Co-Base and Ni-Base Superalloys Fabricated by Electron Beam Melting. Murr, Lawrence; Shujun Li; Yuxing Tian; Amato, Krista; Martinez, Edwin; Medina, Frank // Materials (1996-1944);Apr2011, Vol. 4 Issue 4, p782 

    Reticulated mesh samples of Co-29Cr-6Mo alloy and Ni-21Cr-9Mo-4Nb alloy (625) and stochastic foam samples of Co-29Cr-6Mo alloy fabricated by electron beam melting were characterized by optical metallography, and the dynamic stiffness (Young's modulus) was measured by resonant frequency analysis....

Share

Read the Article

Courtesy of THE LIBRARY OF VIRGINIA

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics