TITLE

Make It Work!

AUTHOR(S)
Kadiani, Asif
PUB. DATE
May 2009
SOURCE
Heating/Piping/Air Conditioning Engineering;May2009, Vol. 81 Issue 5, p11
SOURCE TYPE
Periodical
DOC. TYPE
Article
ABSTRACT
The article provides techniques on how to field-fabricate a tee connection for piping systems with welded joints. It mentions the need to connect the outer diameter of the pipes to fabricate a connection. Moreover, it notes the use of a drafting technique, also known as development of surfaces, in the fabrication of tees in the piping systems.
ACCESSION #
40075475

 

Related Articles

  • Surface sensitivity study of non-gasketed flange joint. Nash, D. H.; Abid, M. // Proceedings of the Institution of Mechanical Engineers -- Part E;2004, Vol. 218 Issue 4, p205 

    From analytical contact pressure studies of gasketed and non-gasketed flanged pipe joints, it is known that good contact maintained over consistently large areas occurs in a no-gasketed flange joint compared with a gasketed joint, where contact is only on the seal ring portion of the gasket....

  • Central Plastics Celebrates 50 Years Of Growth, Innovation. Griffin, Jeff // Underground Construction;Jul2005, Vol. 60 Issue 7, p22 

    Reports on the 50th anniversary of Central Plastics Co., a leading manufacturer of products for joining pipe used in utility, oil field and industrial infrastructures. Number of people employed in worldwide operations of the company; Company's product line which includes mechanical, compression,...

  • Specifying Pipe-Joining Methods. Miller, William C. // Heating/Piping/Air Conditioning Engineering;Nov2004, Vol. 76 Issue 11, p58 

    Discusses joining methods for various types of piping. Parts of threaded joints; Classes of cast-iron and malleable-iron fittings; Pipes that make use of steel welded joints; Way to create a soldered joint; Features of fusion welding. INSET: Selection Issues.

  • High-pressure joint.  // Design News;11/23/92, Vol. 48 Issue 22, p57 

    The article features the pipe swivel flange joint developed by GE Aircraft Engines. This joint use a 90-degree counterbore in the flange to encompass the ferrule. Its design eliminates stress compression and minimize flange distortion. An illustration showing how this device works is presented.

  • Bolt preload scatter and relaxation behaviour during tightening a 4 in-900# flange joint with spiral wound gasket. Abid, M.; Hussain, S. // Proceedings of the Institution of Mechanical Engineers -- Part E;2008, Vol. 222 Issue 2, p123 

    Gasketed bolted flange pipe joints are found prone to leakage during operating conditions. Therefore, performance of a gasketed flange joint is highly dependent on the proper joint assembly with proper gasket, proper gasket seating stress, and proper preloading in the bolts of a joint. For a...

  • Rehabilitation Technology Selection Guide.  // Underground Construction;Jul2005, Vol. 60 Issue 7, p43 

    Presents the Rehabilitation and Technology Selection Guide for the underground construction industry. Cured-in-place-pipe; Folded pipes; Grouts; Internal joint seals.

  • Analyzing stresses in pipe joints to vessels with reinforcing rings. Skopinskii, V. N.; Berkov, N. A.; Rusanov, O. A. // Chemical & Petroleum Engineering;Jul2007, Vol. 43 Issue 7/8, p445 

    Calculations are presented on the state of strain in pipe joints to equipment and pressure vessels used in the chemical and oil industries. Various model approaches are considered for calculating reinforced pipe joints. Calculated results are given for a pipe joint as a welded joint between...

  • Conta baÄŸlantılı PVC boruların deformasyon davranışının laboratuvar deneyleri ile belirlenmesi. Balkaya, Müge; Sağlamer, Ahmet; Moore, Ian D. // ITU Journal Series D: Engineering;Aug2011, Vol. 10 Issue 4, p153 

    Modelling of joints in pipelines is a critical issue influencing both the short and long term performance of these systems. Defects at pipe joints can contribute significantly to reduction of the overall performance of the pipe system. The most common problems attributed to joint defects are...

  • Drawing a powder through a conical die with mobile wall. Generalov, M. B.; Klevleev, V. M.; Kuznetsova, I. A.; Pilyagina, A. O. // Chemical & Petroleum Engineering;Jul2007, Vol. 43 Issue 7/8, p438 

    Theoretical results are presented on the drawing of a powder through a conical die with mobile wall. Analytic formulas are derived for the state of stress and strain in the consolidation and extrusion zones, and for the normal and tangential stresses at the contact surface between the powder and...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics