TITLE

A new inclusion denture marking system

AUTHOR(S)
Oliver, Brian
PUB. DATE
January 1989
SOURCE
Quintessence International;Jan1989, Vol. 20 Issue 1, p21
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
The article presents a study on a new inclusion denture marking system. Several methods and techniques were followed in the study for the production of a tag that would be unobtrusive in the finished denture and leaves the name of the patient highlighted beneath the polished surface. A soaking routine was followed and the effect of a name tag insert on the strength of the denture was assessed. It has been concluded that a spirit pen can be used for writing the name of the patient on a processed strip of heat cured acrylic resin denture-base material. It was also found that the insertion of the tag into the denture at the trial closure stage has no negative effect upon the finished denture's strength and a cleaning regime had little harmful effect upon the readability of the name.
ACCESSION #
38814744

 

Related Articles

  • A computer-aided, program driven machine used to calculate the interface between master cast and acrylic resin denture. Rimpault, Lionel; Couetard, Y.; Debadie, M. // Quintessence of Dental Technology (QDT);1992, Vol. 15, p105 

    The article discusses a study which investigated the accuracy of reproducing acrylic resin denture base that was processed against an edentulous master cast. The master casts utilized in the study were obtained by duplicating the original patient master cast. The study used a three-dimensional...

  • Effect of chemical surface treatments and repair material on transverse strength of repaired acrylic denture resin. Vojdani, Mahroo; Rezaei, Sakineh; Zareeian, Lila // Indian Journal of Dental Research;Jan-Mar2008, Vol. 19 Issue 1, p2 

    Purpose: This study was performed to evaluate the transverse strength of a denture base resin (H), repaired with an autopolymerizing acrylic resin (A) or a visible light-curing (VLC) resin (T) following the use of three chemical solvents: methyl methacrylate monomer, aceton or chloroform....

  • ISPITIVANJE ÄŒVRSTINE VEZE IZMEĐU PLOÄŒASTIH ZUBNIH PROTEZA I MATERIJALA ZA IZRADU MEKOG PODLAGANJA. Petković, Dušan Lj.; Krunić, Nebojša S.; Kostić, Milena M.; Petrović, Dimitrije M.; Radenković, Goran M. // Acta Stomatologica Naissi;Dec2012, Vol. 28 Issue 66, p1171 

    Introduction. In clinical practice, the loss of adhesion between the denture base resin and reliner might cause the loss of material softness, water sorption, bacterial colonization and functional failure of the prosthesis. Aim. This study evaluated the effect of immersion on tensile bond...

  • Fracture Strength of Resin-Bonded Dental Prostheses with a Rigid Versus Nonrigid Joint. An In Vitro Study. Cleuren, Katrien M. L.; Vandamme, Katleen; Naert, Ignace // International Journal of Prosthodontics;2009, Vol. 22 Issue 2, p140 

    This in vitro study investigated whether a resin-bonded dental prosthesis (RBDP) with a hyperstatic, rigid joint was preferable to an isostatic, nonrigid construction in terms of debonding and fracture strength. RBDPs replacing a missing molar with a rigid (design I) or a resilient model (design...

  • A Rationale and Technique for Constructing Adjustable Palatal Lift Prostheses. Ramsey, W. O.; Dertegri, P. F.; Baier, R. G. // International Journal of Periodontics & Restorative Dentistry;1982, Vol. 2 Issue 5, p22 

    The article focuses on the construction of horizontally adjustable dental prostheses for supporting a neurologically impaired soft palate. A typical palatal lift prosthesis consists of an anterior maxillary denture base containing a cast unit, a wire connector and an arbitrarily formed velum...

  • Bond Strength Variation of Synthetic Resin Teeth in Dentures. Cunningham, J. Leo; Benington, Ian C. // International Journal of Prosthodontics;Jan/Feb1995, Vol. 8 Issue 1, p69 

    The bond strength of denture teeth to acrylic resin denture bases was determined by producing tensile test specimens from standardised and anonymously presented partial dentures. Ten dentures were produced by randomly selected commercial dental laboratories and five were produced in a university...

  • Porosity in denture acrylic resins cured by microwave energy. Sanders, John L.; Levin, Bornard; Reitz, Phillip V. // Quintessence International;Jul1987, Vol. 18 Issue 7, p453 

    The article offers information on a dental research conducted in order to determine the differences in the amount of porosity of acrylic resin used in making artificial dentures and treated by microwave energy. For the research, two different methods of microwave processing were compared. Five...

  • In Vivo Heat Transfer Capacities of Autopolymerizing, Heat-Polymerizing, and Injection-Molded Acrylic Resins. Oruc, Selcuk; Usumez, Aslihan; Enhos, Dilek Simsek; Ozturk, Nilgun // International Journal of Prosthodontics;Nov/Dec2006, Vol. 19 Issue 6, p618 

    The aim of this pilot study was to measure the heat transfer capacities of heat-polymerizing, injection-molded, and autopolymerizing acrylic resins in vivo. Two volunteers used acrylic resin removable plates and consumed hot (69°C) and cold drinks (6°C). Differences between oral...

  • Skinning cats. Nikoloski, Jordan // eLABORATE;May/Jun2009, p52 

    The article provides information on heat cure processing of dentures with acrylic teeth. According to the article, there are seven deadly sins or errors involving heat cure processing of dentures with acrylic teeth, including increased occlusal vertical dimension (OVD) or raised bite, poor...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics