Development of scientific investigations in the field of corrosion and corrosion protection of materials in Ukraine

Pokhmurs’kyi, V.
September 2008
Materials Science;Sep2008, Vol. 44 Issue 5, p609
Academic Journal
The article discusses various studies that investigate the corrosion and corrosion protection of materials in Ukraine. The study conducted by researchers headed by H. V. Samsonov, I. M. Fedorchenko and other experts in the field of development of new composite materials and coating is cited. Meanwhile, a study was also conducted on the nature and mechanisms of corrosion damage to the elements of reactors at nuclear power plants depending on the period of operation and operating conditions.


Related Articles

  • Utilities fight corrosion and erosion battle endlessly. Stein, Henry // Electric Light & Power;Jul93, Vol. 71 Issue 7, p10 

    Reports on the corrosion and erosion problems of nuclear power plants in the U.S. Factor causing the corrosion and pitting of alloys; Corrosion rates of the alloys; Cost of corrosion in light-water plants.

  • CRACKS UNCOVERED BY CAT-SCAN-LIKE INSPECTIONS OF BUSINESS JETS. Rosenberg, Barry // Aviation Week & Space Technology;8/18/2003, Vol. 159 Issue 7, p65 

    The Structural Anomaly Mapping (SAM) is used to uncover cracks and corrosion in metal, and debonding and delamination in composites. SAM can be programmed to inspect a super-midsize to large aircraft in 10-12 hour, moving all around it and examining every part to create a three-dimensional...

  • Thermal and anticorrosive properties of polyurethane/clay nanocomposites. Chen-Yang, Y.; Yang, H.; Li, G.; Li, Y. // Journal of Polymer Research;Dec2004, Vol. 11 Issue 4, p275 

    A montmorillonite clay has been modified with two different quaternary ammonium salts, dilauryldimethylammonium bromide (LD) and 4,4'-diaminodiphenylmethane (AP), to form the corresponding organophilic clays, LDM and APM. Two series of PU/clay nanocomposite materials, PU/LDM and PU/APM, were...

  • Corrosion-resistant composite materials based on AlN-Al2O3 with (Ni-Cr-Al) metal binder. Lavrenko, V.; Panasyuk, A.; Neshpor, I.; Belykh, A. // Refractories & Industrial Ceramics;Nov2006, Vol. 47 Issue 6, p373 

    The specifics of high-temperature air corrosion of composite cermet materials of the system (AlN-Al2O3)-(Ni-Cr-Al) are considered. The oxidation kinetics is studied by thermogravimetric (TG) and differential thermal analysis (DTA) methods on compact samples and on the respective composite...

  • Influence of high temperature and high acidic conditions on geopolymeric composite material for steel pickling tanks. Deeptangshu Chaudhary; Huihua Liu // Journal of Materials Science;Aug2009, Vol. 44 Issue 16, p4472 

    Traditionally, most equipment that was used for containing corrosive solutions and fumes for the steel industry was fabricated from steel with a rubber-lined interior. An additional acid-resistant brick lining was used to protect the rubber lining and also to act as thermal insulation. This...

  • Electrodeposition and Corrosion Properties of Zn-VO Composite Coatings. Bindiya, S.; Basavanna, S.; Arthoba Naik, Y. // Journal of Materials Engineering & Performance;Sep2012, Vol. 21 Issue 9, p1879 

    Composite coatings were obtained by electrochemical codeposition of VO nanoparticles with zinc, from an additive free acid sulfate bath. The corrosion behavior of electrodeposited Zn and Zn-VO composite coatings was investigated in 3.5% NaCl solution using polarization and electrochemical...

  • Electro-Synthesis of Nano-Colloidal PANI/ND Composite for Enhancement of Corrosion-Protection Effect of PANI Coatings. Ashassi-Sorkhabi, Habib; Es’haghi, Moosa // Journal of Materials Engineering & Performance;Dec2013, Vol. 22 Issue 12, p3755 

    The polyaniline/nanodiamond (PANI/ND) nanocomposite coating was prepared on mild steel via electrochemical polymerization using cyclic voltammetry technique. The ultrasonic irradiation was used for effectively dispersing ND particles in electropolymerization solution. The prepared nanocomposite...

  • Approaches for evaluating composite materials used in a variety of piping designs. MARTIN, ROD // JEC Composites Magazine;May/Jun2015, Issue 97, p51 

    The article focuses on the significance of composite materials for gas and oil companies in Great Britain. Topics discussed include the use of composites for piping systems, various characteristics of composite materials such as spoolability and flexibility, and the advantage of composites for...

  • Corrosion behaviour of magnesium-yttria composite sintered by microwave hybrid heating. Tamang, S.; Potaliya, P.; Aravindan, S. // Materials Research Innovations;Nov2018, Vol. 22 Issue 7, p422 

    Requirement of light weight, high strength and good corrosion resistance structures can be fulfilled by using magnesium alloy metal matrix composites. Powder metallurgy route of manufacturing these composites is studied in this work. Magnesium alloy with yttria reinforcement particles of 5-10...


Read the Article


Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics