TITLE

Experimental Studies on Turning of Discontinuously Reinforced Aluminium Composites under Dry, Oil Water Emulsion and Steam Lubricated Conditions Using TAGUCHPs Technique

AUTHOR(S)
Shetty, Raviraj; Pai, R.; Rao, S. S.
PUB. DATE
January 2009
SOURCE
Gazi University Journal of Science;Jan2009, Vol. 22 Issue 1, p21
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
No abstract available.
ACCESSION #
37038240

 

Related Articles

  • Experimental investigation of soyabean oil based cutting fluid during turning of hardened AISI 4340 steel with Minimal Fluid Application. Raj, Anil; Wins, K. Leo Dev; George, Kiran Easow; Varadarajan, A. S. // Applied Mechanics & Materials;2015, Vol. 813/814, p337 

    Turning of hardened steel is normally carried out with copious supply of cutting fluid to improve the cutting performance. Most of the cutting fluids in regular use are petroleum based emulsions which create several environmental problems. In this context, pure dry turning is a logical...

  • Experimental Study on Milling Formation and Milling force in Green Machining Ti6Al4V. Hui Wang; Fusheng Ni; Xiulin Ji // Applied Mechanics & Materials;2014, Vol. 727-728, p65 

    The machinability of Titanium alloy Ti6Al4V is poor, so the new green cutting technology with water vapor and ionized air as coolants and lubricants was proposed to achieve the aim of efficient and green cutting for Ti6Al4V. In this paper, the milling formation and milling force were studied in...

  • Research on the Formation Mechanism of Emulsion Spots on the Cold-rolled Silicon Steel Surface. Yan Li; Jianlin Sun; Jingyue Chen // Materials Science Forum;2016, Vol. 850, p809 

    For the cold-rolled silicon steel strip lubricated with emulsion, the typical oil spot defects always can be found on the surface of rolled strip. The oil spot are parallel to the rolling direction. In the present study the micro-structure of oil spot defects was investigated by several surface...

  • Performance evaluation and optimization of nano boric acid powder weight percentage mixed with vegetable oil using the Taguchi approach. Pavani, P.; Pola Rao, R.; Srikiran, S. // Journal of Mechanical Science & Technology;Nov2015, Vol. 29 Issue 11, p4877 

    Turning, which is a widely employed method of metal removal process in manufacturing industries, generates many temperatures because of the increase in cutting forces. In view of the high temperatures developed in the process, tools deteriorate, and so good surface quality is difficult to...

  • Formulation of Cold Pressed-Coconut Oil Dry Emulsion. Chomto, Parichat; Gaysorn Chansiri; Khaw-on Tepsukon; Yodwandee, Pawitra; Porntipa Laovanichkul; Somlak Kongmuang // Advanced Materials Research;2014, Vol. 1060, p91 

    Development of stable dry emulsion capable to self-reform into emulsion by reconstitution in water is presented. The major compositions of oil in water (o/w) emulsion were cold pressed-coconut oil (or virgin coconut oil from four different companies) as oil phase and water as phase containing an...

  • Temperatures in fine grinding with minimum quantity lubrication (MQL). Morgan, M.; Barczak, L.; Batako, A. // International Journal of Advanced Manufacturing Technology;Jun2012, Vol. 60 Issue 9-12, p951 

    Minimum quantity lubrication (MQL) is a promising new fluid delivery technique in grinding. However, the thermal behaviour of the process under such cooling conditions remains unclear. This work reports on the results of a recent investigation of MQL in fine-cut plane surface grinding. The...

  • Tomography Observation of Fiber Reinforced Composites After Fatigue Testing. Bale, Jefri; Valot, Emmanuel; Monin, Martine; Polit, Olivier; Bathias, Claude; Soemardi, Tresna // Applied Mechanics & Materials;2015, Vol. 799-800, p937 

    This work presented an experimental study to observe the inside conditions and damage appearances of fiber reinforced composites material by non destructive testing (NDT) method. In order to achieve this, an open hole specimen of unidirectional glass fiber composite (GFRP) and discontinuous...

  • COLD AIR DRY MACHINING Part 1: EXPERIMENTAL SETUP. Ekinović, Sabahudin; Begović, Edin; Fakić, Belma; Burić, Adisa; Čeliković, Aida // Journal of Trends in the Development of Machinery & Associated T;2014, Vol. 18 Issue 1, p39 

    Dry machining and near-dry machining were developed as an alternative to flood and internal high-pressure coolant supply to reduce metal working fluids consuption. In dry machining, compressed air introduces into the cutting zone, while near-dry machining supplies very small quantities of...

  • 稠油乳化输送试验环道装置研制及应用. 寇杰; 张新策; 刘建国 // Research & Exploration in Laboratory;2015, Vol. 34 Issue 11, p60 

    In order to study the flow characteristic of heavy oil emulsion in the actual pipeline and to make up for the shortcomings of rheology instrument, a test loop device is developed. The authors used this device to carry out transporting test for the heavy oil of Chennan in Shenli, and simulated...

  • Effects of spray-drying on w/o/w multiple emulsions prepared from a stearic acid matrix. Mlalila, Nichrous; Swai, Hulda; Kalombo, Lonji; Hilonga, Askwar // Nanotechnology, Science & Applications;2014, Vol. 7, p105 

    The goal of this study was to explore the effects of spray-drying on w/o/w double emulsions of methyltestosterone (MT) loaded in a stearic acid matrix. MT-loaded nanoparticles were formulated by a water-in-oil-in-water emulsion technique using 50, 75, and 100 mg of stearic acid, 2% and 3% w/v...

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics