TITLE

The Tensile and Shear Strength of a Base Metal Weld Joint Used in Dentistry

AUTHOR(S)
MacENTEE, M. I.; HAWBOLT, E. B.; ZAHEL, J. I.
PUB. DATE
February 1981
SOURCE
Journal of Dental Research;Feb1981, Vol. 60 Issue 2, p154
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
Samples of a base metal alloy were cast and welded together using a conventional welding procedure. The joints were loaded and placed either in a corrosive environment or in air for varying time periods. The tensile and shear strength of the joints was unaffected by the corrosive environment, and the joints, despite some internal defects, appeared suitable for clinical use.
ACCESSION #
36508808

 

Related Articles

  • Metallic glasses: Must shear bands be hot? Spaepen, Frans // Nature Materials;Jan2006, Vol. 5 Issue 1, p7 

    The article discusses the mechanical properties of metallic glasses. A metallic glass is produced by cooling an alloy melt under conditions that prevent crystallization. Yet, the material is said to deform. In the plastic deformation of metals at low temperatures, the smaller the crystals that...

  • Shear strength measurements in the TiAl-based alloy Ti–48Al–2Nb–2Cr–1B during shock loading. Millett, J. C. F.; Bourne, N. K.; Jones, I. P. // Journal of Applied Physics;8/1/2001, Vol. 90 Issue 3 

    The lateral stress in a titanium aluminide alloy has been investigated under different impact conditions during shock loading, using embedded manganin stress gauges. From this, the variation of the materials shear strength with longitudinal stress has been determined. Results show that shear...

  • Adiabatic shear band in a Ti-3Al-5Mo-4.5V Titanium alloy. Wang, B. F. // Journal of Materials Science;Mar2008, Vol. 43 Issue 5, p1576 

    An investigation has been carried out on the adiabatic shear band (ASB) in a Ti-3Al-5Mo-4.5V (TC16) alloy deformed at high strain rate by a split Hopkinson pressure bar (SHPB). ASB in TC16 alloy is a “white” band with a width of about 13 μm. Microhardness of the ASB is larger than...

  • Cracking of AFNOR 7020 Aluminum Alloy Adaptor Used for Aerospace Applications: A Metallurgical Investigation. Jha, Abhay; Sirisha, G.; Narayanan, P.; Sreekumar, K. // Journal of Failure Analysis & Prevention;Oct2009, Vol. 9 Issue 5, p414 

    Aluminum alloys are frequently preferred materials for aerospace applications due to their high-specific density, high-specific stiffness, and ease of fabrication. In one such application, adaptors used in the torroidal shaped water tank of liquid propulsion system, were made of an AFNOR 7020...

  • The Self-Organized Critical Behavior in Pd-based Bulk Metallic Glass. Zhong Wang; Jiaojiao Li; Wei Zhang; Junwei Qiao; Baocheng Wang // Metals (2075-4701);2015, Vol. 5 Issue 3, p1188 

    Bulk metallic glasses (BMGs) deform irreversibly through shear banding manifested as serrated-flow behavior during compressive tests. The strain-rate-dependent plasticity under uniaxial compression at the strain rates of 2 × 10-2, 2 × 10-3, and 2 × 10-4·s-1 in a Pd-based BMG is...

  • Improvement in Fatigue Performance of Aluminium Alloy Welded Joints by Laser Shock Peening in a Dynamic Strain Aging Temperature Regime. Chun Su; Jianzhong Zhou; Xiankai Meng; Shu Huang // Materials (1996-1944);Oct2016, Vol. 9 Issue 10, p799 

    As a new treatment process after welding, the process parameters of laser shock peening (LSP) in dynamic strain aging (DSA) temperature regimes can be precisely controlled, and the process is a non-contact one. The effects of LSP at elevated temperatures on the distribution of the surface...

  • CALCULATION OF MODE PARAMETERS OF WALL BEAD DEPOSITION IN DOWNHAND MULTI-PASS GAS-SHIELDED WELDING. SHOLOKHOV, M. A.; BUZORINA, D. S. // Paton Welding Journal;Jul2013, Issue 7, p61 

    Application of narrowed grooves is an effective method to increase welding process efficiency at simultaneous reduction of financial and energy expenses. One of the main difficulties in implementation of multi-pass welding technology 10 mm thick rolled metal structures using automated and...

  • Fatigue crack propagation behavior of friction stir welded 5083-H32 Al alloy. Hong, Seongjin; Kim, Sangshik; Lee, Chang Gil; Kim, Sung-Joon // Journal of Materials Science;Dec2007, Vol. 42 Issue 23, p9888 

    Fatigue crack propagation (FCP) behavior of friction stir welded (FSWed) 5083-H32 Al alloy was examined with the fatigue crack growing either along the dynamically recrystallized zone (DXZ) at variable Δ K or perpendicular to the DXZ at a constant Δ K value of 10, 13, 15, and 17...

  • Dose Dependence of Strength After Low-Temperature Irradiation in Metallic Materials. Byun, Thak; Li, Meimei; Farrell, Kenneth // Metallurgical & Materials Transactions. Part A;Jan2013 Supplement, Vol. 44, p84 

    This study intends to review and characterize the low-temperature (<473 K [200 °C]) irradiation-hardening behaviors in metallic materials and to propose new interpretations on the dose dependence of strength, particularly in the prehardening and saturation regimes. The analysis of results of...

Share

Read the Article

Courtesy of NEW JERSEY STATE LIBRARY

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics