TITLE

Multichannel filters via Γ-M and Γ-K waveguide coupling in two-dimensional triangular-lattice photonic crystal slabs

AUTHOR(S)
Ya-Zhao Liu; Rong-Juan Liu; Shuai Feng; Cheng Ren; Hai-Fang Yang; Dao-Zhong Zhang; Zhi-Yuan Li
PUB. DATE
December 2008
SOURCE
Applied Physics Letters;12/15/2008, Vol. 93 Issue 24, p241107
SOURCE TYPE
Academic Journal
DOC. TYPE
Article
ABSTRACT
We demonstrate the design, fabrication, and characterization of a multichannel filter in a two-dimensional triangular-lattice photonic crystal slab. The output signal channel, which directs in the Γ-M crystalline direction, is orthogonal to the input signal channel that directs in the Γ-K crystalline direction. In each channel, the filtering function is guaranteed by the indirect resonant coupling between the waveguide and the cavity. Four resonant cavities with different sizes provide the mechanism of finely tuning the output wavelength. Our experimental results are in good agreement with simulations.
ACCESSION #
35922150

 

Related Articles

  • Holmium-doped silica fiber designs extend fiber lasers beyond 2 μ. Samson, Bryce; Oulundsen, George; Carter, Adrian; Bowman, Steven R. // Laser Focus World;Aug2012, Vol. 48 Issue 8, p47 

    The article offers information on fabrication of optical fiber to extend fiber lasers beyond 2 micrometer. It states that a 140 W, 2.13 micrometer mid-infrared fiber laser operating with 60 percent slope efficiency is possible using holmium-doped silica fibres operating at the long wavelength...

  • Low divergence single-mode surface emitting quantum cascade ring lasers. Mujagić, E.; Hoffmann, L. K.; Schartner, S.; Nobile, M.; Schrenk, W.; Semtsiv, M. P.; Wienold, M.; Masselink, W. T.; Strasser, G. // Applied Physics Letters;10/20/2008, Vol. 93 Issue 16, p161101 

    We describe the fabrication and operation of surface emitting second-order distributed feedback quantum cascade ring lasers. The devices exhibit single-mode emission at a wavelength of 3.95 μm with a side mode suppression ratio of 25 dB. A linear tuning coefficient of 0.13 cm-1/K is observed....

  • Observation of whispering gallery modes in nanocrystalline diamond microdisks. Wang, C. F.; Choi, Y-S.; Lee, J. C.; Hu, E. L.; Yang, J.; Butler, J. E. // Applied Physics Letters;2/19/2007, Vol. 90 Issue 8, p081110 

    Nanocrystalline diamond microdisks have been fabricated and characterized. The process conditions were chosen to ensure smooth and vertical sidewalls. Focused ion beam milling was used to create ultrasmooth sidewalls. Whispering gallery modes were observed near the nitrogen-vacancy center...

  • State-of-the-art product expansion in Minnesota. Reis, Michael // Stone World;Feb2010, Vol. 27 Issue 2, p48 

    The article presents a case study on the business expansion of Innovative Surfaces Inc. of Hastings, Minnesota into stone fabrication and investments in stoneworking technology in Minnesota. Bruce Atkins, owner of Innovative Surfaces, states that the investments have added new level of...

  • Fabrication and design of an integrable subwavelength ultrabroadband dielectric mirror. Lu Chen; Huang, Michael C. Y.; Mateus, Carlos F. R.; Chang-Hasnain, Connie J.; Suzuki, Y. // Applied Physics Letters;1/16/2006, Vol. 88 Issue 3, p031102 

    We have designed and fabricated a subwavelength grating (SWG) broadband mirror whose performance depends on key factors, including SWG period, duty cycle, and angle of incident light. The fabricated SWGs exhibit high reflectivity (>=96%), when the grating periods are varied from 650 to 750 nm...

  • Fabrication of 5-7 nm wide etched lines in silicon using 100 keV electron-beam lithography and.... Wei Chen; Ahmed, Haroon // Applied Physics Letters;3/29/1993, Vol. 62 Issue 13, p1499 

    Demonstrates the fabrication of wide etched lines in Si using electron-beam lithography and polymethylmethacrylate (PMMA) resist. Mechanisms in determining the development of linewidth in resist; Importance of intermolecular force in determining PMMA properties; Elimination of resist swelling...

  • Rapid prototyping. Berard, M.F. // Ceramic Industry;Dec97, Vol. 147 Issue 13, p78 

    Discusses some rapid prototyping (RP) and solid free-form fabrication (SFF) tools of manufacturing organizations. Technological advances in RP; Discussion of stereolithography; Use of ultraviolet light exposure for prototyping.

  • THE FABRICATION SHOP. Murphy, Patrick // Air Conditioning Heating & Refrigeration News;10/28/2002, Vol. 217 Issue 9, p24 

    Presents a questionnaire on fabrication shop.

  • Managinng Moisture: Will Your Fabric Keep You Comfortable? Wyman, Diana A. // Colourage;Sep2008 Supplement, Vol. 55 Issue 9, p6 

    The article discusses various topics published within the issue including one about the use of fabric test to determine the amount of liquid absorbed, and another one about the method for measuring the wicking rate of a fabric.

Share

Read the Article

Courtesy of VIRGINIA BEACH PUBLIC LIBRARY AND SYSTEM

Sorry, but this item is not currently available from your library.

Try another library?
Sign out of this library

Other Topics